Jump to content
SAU Community

Digital Fuel Adjuster, Jaycar

chrisgero

By chrisgero,
in Engines & Forced Induction

 Share

Recommended Posts

chrisgero Contributor

chrisgero

Posted
Posted

Anyone,

Could I please get your feedback on the Jaycar Fuel and air adjuster. I explored one of the threads that mentioned the jaycar system and it was intresting.

jaycar.com.au

go to

Kits and Modules and Auto and you will find it at the bottom of the page. You have to purchase the hand controller.

I would like to get feedback from anyone who has actually installed the Jaycar system in their skyline Turbo.

what I want to know, should I pay for a cheap alternative or go for the SAFCII or the E-Manage expensive allternative just to alter my fuel and air.

I appreciate your help

chris G

Link to comment
https://www.sau.com.au/forums/topic/83974-digital-fuel-adjuster-jaycar/
Share on other sites
Panikin Collaborator

Panikin

Posted
Posted

DFA will do the job quite nicely. search the stagea disscussion board for more info, Sydneykid is the one who created the thread and has a good wrap for them.

I have yet to tune mine but it was not to hard to install PM me for a wiring diagram for it and the iebc.

  • 2 weeks later...
chrisgero Contributor

chrisgero

Posted
  • Author
Posted
DFA will do the job quite nicely. search the stagea disscussion board for more info, Sydneykid is the one who created the thread and has a good wrap for them.

I have yet to tune mine but it was not to hard to install PM me for a wiring diagram for it and the iebc.

Panikin,

It would be really good if you can send me some photos and installation guide. I just want to make the right choice when buying the jaycar kit or I purchase the SAFCII. If i purchase the kit then i will get a bigger dump pipe and install it myself. I should gain some horse power.

I look forward to your reply.

Chris G

xRHETTx Mentor

xRHETTx

Posted
Posted

Ive made mine and installed it, but havent tuned it yet.

It was all pretty easy, you just have to be careful.

Get the DFA and dont waste ur money on a SAFC for 3 times the price. It does exactly the same thing.

Emanage is a bit different because it has other bits you can add on eg. ignition timing.

All instructions and photos are in the Silicon Chip book Performance Electronics for Cars. Get the book and have a read, its all good.

Note that if you have an r32 you will have to get a r33 boost solendoid, which'll cost an extra few bucks ($40 maybe)

Sydneykid Grand Master

Sydneykid

Posted
Posted

Every question you can think of has probably been answered in this thread http://www.skylinesaustralia.com/forums/in...showtopic=61207

There are heaps of pictures and diagrams as well.

If you have one that hasn't been asked yet, please ask away in the above thread and I will try my best to answer it.

:( cheers :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...