Jump to content
SAU Community

Recommended Posts

hi guys,

ok let me paint a picture,

i have a 33, with some mods, and makes some power,

i have a bosche 040 supplying fuel to standard injectors with a stock pressure reg

this is my second bosche pump (will explain in due course)

after about 100kms of hard mtn terrain in the crisp hrs of teh morning, the pump gets very noisy and the car starts to miss.

i stopped and pulled teh pump out,

no signs of anything blocking it, mesh looked nice and clean.

however i did notice that all the fuel in the tank was rather warm, heaps warmer then fuel normally is.

anyway, put the pump back in, filled up with gas and drove on,

about 40 kms further along the drive, same issue started up again. car starts to miss under load, and even at very low revs,

cars becomes completely undriveable

wen i stop the car i hear the very noisy pump whinning like a virgin being broken in by a big black african warrior.

once the pump cools down (i ssume its cooled down casuse the noise stops) it starts to work fine again.

so what do i do?

get another pump, (i sent the last one back when it started to do this)

or is it something else?

any ideas and comments will be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/
Share on other sites

I recently got an 040 installed intank in my 33 GTST, to replace the stocker.

Only issue I had is that I couldn't get the pump as far down as the standard one (due to the design of the pickup), but I've got no problems with that because I'm able to keep my car filled to at least a 1/4 tank at all times.

Apart from that, you wouldn't be able to tell it's an aftermarket pump. No extra noise, the car doesn't take any longer to start, and I'm totally happy with it.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521108
Share on other sites

neil: sounds like its not getting enough current, therefore not working to its full efficiency. Probably the heat is the sign of it working much harder than it should (which like u say will result in a failure eventually)

might have to run some thicker cabling to the pump..

Something to investigate anyhow.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521490
Share on other sites

mate.i had a similar problem,sounds to me that you have a fuel block,first i would look at your fuel reg pressure,cause of this means if it is blocked or not functioning properly means no fuel is returning back to tank.at this stage fuel pressure is building up in your fuel rail sending too much fuel thru your injectors which floods the spark plugs causing miss.I suggest checking fuel pressure at in take and return.Its happened to me,also happens after 20mins of driving with same symptoms.In my case it was the fuel reg.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/83981-fuel-pump-issues/#findComment-1521711
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you go about diagnosing ecu's that don't have data logging, is it more experience at that point and just trying out things that you think will fix the issue?
    • Stock O2 are basically useless beyond anything at stoich. Any misfire will also be seen as lean. The stock O2 also read a collective exhaust gas volume, not each cylinder. Sputtering and missing means not each cycle is firing, and some are. Which means even if rich, as shit, on cylinders as they miss, they'll read lean, but the cylinders that did fire will read rich, and combined, well, they can read anything from rich to lean.   Start with the basics before even going looking at sensor values.   Edit: I say the above, and that's coming from the guy with a few thousand dollars worth of scan tools sitting right beside me right now that I use frequently for my job.
    • I just finished up a manual swap and I have a 1999 S2 AWD automatic in my garage, depending on where you are located. I'm in the the midwest of the US.
    • I’ve heard it can be done, you need to redrill the holes where they bolt to the chassis and apart from that they are the same. I’ve never done it or know anyone personally that has, it’s just something I’ve heard 
    • If it's reading full rich prior to a misfire that gives one directional hint, if it's already reading lean, etc. If it's reading pretty cleanly stoichiometric then suddenly drops out from a misfire that suggests it's not air mass estimation that's the problem. Could be ignition, could be something more subtle. Could be the CAS has decided to start dropping out at random or the drive pin is worn leading to excessive lash and trigger errors. LTFT can tell you the same but it's slower to react and if this is a recent issue it might not have stabilized. STFT stuck in one direction vs fluctuating back and forth can be used instead but I like to read O2 voltages anyways and interpret directly. If the O2 voltages make no sense in general or are super slow to react it could also be a failing O2 sensor. There's no real error correction for failing O2 sensors in these cars.
×
×
  • Create New...