Jump to content
SAU Community

Recommended Posts

Hey guys,

Have narrowed my choice of rims down to two (for my 32 gts-t):

1. F: 18x8.5 +22

R: 18x9.5 +22

2. F: 18x9.5 +18

R: 18x9.5 +18

I realize the second option is quite aggressive, especially for a gts-t front, and would probably require lot of camber and stretching.

Thoughts? Opinions? All welcome...Thanks

Brake clearance, depend on rim design - what rims are you getting btw?

You'd need to run 245/40 tyres and roll the guards for sure. And maybe dial some camber for good measure.

Hey guys,

Have narrowed my choice of rims down to two (for my 32 gts-t):

1. F: 18x8.5 +22

R: 18x9.5 +22

2. F: 18x9.5 +18

R: 18x9.5 +18

I realize the second option is quite aggressive, especially for a gts-t front, and would probably require lot of camber and stretching.

Thoughts? Opinions? All welcome...Thanks

I'd go for 2nd option if you don't mind doing the work required to fit. It'll look tough kinda reminded me of Abu's old R32 GTST.

1st option seems to be safe.

Really, it's up to you as in how prepared you are to make it fit.

Brake clearance will depend on the wheels design mostly, not offset.

They will hang out of your guards roughly 10-15mm so yes depending on how low you go you'll wanna roll and maybe flare your guards depeding on tyre width.

Brake clearance, depend on rim design - what rims are you getting btw?

You'd need to run 245/40 tyres and roll the guards for sure. And maybe dial some camber for good measure.

volk te37

Brake clearance will depend on the wheels design mostly, not offset.

They will hang out of your guards roughly 10-15mm so yes depending on how low you go you'll wanna roll and maybe flare your guards depeding on tyre width.

Would a 19x10.5 + 12 all round, be suited better ?

What do you guys recommend ?

*edit* also what tyres all round ? 245, 255 ?

Edited by KISIN

TE37 have plenty of room to fit big brakes especially 19" diameter rims.

19x10.5 +12 is better suited for 33 GT-R.

As for tyres, 265/35 or 275/35, 33 GTR have plenty of room under the guards, maybe a minor guard lipping would suffice but once again it's up to tyres style.

+12 is perfect, I've got 10" +12s, sits maybe 2mm out of the guards.

Will have a chunky-ish kit put on so im worried they will look sunk in the guards...but i think it should be spot on then with 19x10.5 +12 and 275's....

thanks guys!!

r33 1998

20 inch

8.5 wide

35 offset

225 front 245 rear

look nice big 20s but everyday driving car being lowered almost 2 inches had to roll guards and remove innner plastic

you really feel the bumps and really have to watch out for pot holes .19s or smaller are probably better for everyday but something always have to be compromised looks or performance.

  • 3 weeks later...

Skyline model = R31 Aus Spec

Wheel diameter = 18in

Wheel width = 7.5in

Wheel Offset = 40

Tyre size = 225/40

Modifications to fit = 5mm Spaces On Front to clear Strut/Spring Plate, 30mm bolt ons for the rear ONLY for looks.

Looking at putting

F - 19x8 - 55 Offset

R - 19x10 - 37.5 Offset

Recon these will fit?

Hey everyone, Need help before i buy new wheels!

Wheels: Work Emortion 11R 18x9.5 +12 all round on a R34 25GT

Thinking I'll need stretched tyres and rolled guards ?... Anything else ?

Help greatly appreciated and thanks in advanced !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If you are genuinely considering trying to get this engineered, I would strongly advise finding the engineer that is happy to sign that off first before you put the hole in your car.  I've seen cars get defected for this and not be able to be put back on the road as no engineer they spoke to was happy to sign if off.  
    • Apologies, while id like to put the MAF as close to the TB and relocate the recirc, this may be too much work. Will most likely end up just putting it on the original AFM spot ( onto/next to the airbox ).  Was going through nistune, found a pretty nifty doc on this. Nistune MAF Notes. Also, i was looking through the bay, and there seems to be a tube/line connected from the A/C to the intercooler piping ( Between the smic and the recirc), what does this do as the crossover fmic piping doesnt have any connection? plumbing? not sure what you call it but the nipple thing ahah.  Also, been reading up more about crossover fmic in regards to the legality of having the hole drilled for the piping, this would most likely need to be engineered right?
    • My advice is if you need a big build done do it in Japan. The yen rate is so favorable and there are shops that can be genuinely trusted and not micromanaged/carefully monitored every step of the way. Garage Yoshida is obviously my preferred option but they're so busy these days and all interaction with new customers has to be mediated through BBL/Toprank now. 
    • I haven't....but a poorly made one would terrify me. Surely a good second hand one is the go, as they don't work hard and no-one wants to keep one after they are finished with it A big consideration would be the weight of the shell you are putting on it....is it a fully dressed chassis or just the body
×
×
  • Create New...