Jump to content
SAU Community

Recommended Posts

Hello,

I`m about to do manual conversion of my 1997 ENR33 (GTS-4, RB25DE) (yeah, i used search, but some questions still remain).

Now i have a kit of:

- brake and clutch pedals from HR33, RB20E

- cluth master cylinder and pipng from RB20E

- ENR34 manual g-box + stock clutch + ENR34 flywheel + clutch slave cylinder

- rubber boot + console shifter cover

- 4l of Nissan PSF Special (ATTESA fluid)

- spigot bush + various nuts and bolts.

The mechanical part of conversion is not a problem. The problem is electrical part. I know that i have to shortcut the inhibitor relay for engine to start. Also, i need to ground pin N44 (neutral switch) cause it affects the ignition timing somehow (what is it for?). And also i have to wire in the speed sensor.

Questions:

1. i can`t find full wiring diagram for R33, especially for 4wd one`s. What are the wire colours that i need for neutral switch, reverse lights and speed sensor?

2. What wires must be connected for proper work of ATTESA E-TS?

3. Can i use ECU from N/A MT R33 Skyline without ATTESA on my GTS-4 straight bolt-on? Or i need a special one for GTS-4 with ATTESA support?

4. Can i leave my AT dashboard after installing the MT5? Will the speedometer show correct speed? The final drive ratios in AT and MT ENR33 are equal.

p.s. thank you in advance and sorry for my english -- it`s not my native language.

Link to comment
https://www.sau.com.au/forums/topic/84531-enr33-gts-4-auto-2-manual-conversion/
Share on other sites

  • 16 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's right, simple but works. Run out of load? Rescale the table lol. Want to be lazy and not rescale? Drag the K
    • @DraftySquash @Duncan he's not talking about the part that sits against the radiator support, he’s talking about the lip that sits towards the front outside of the car. anyway I had a look at other cooling panels and came across this one https://justjap.com/products/carbing-radiator-cooling-panel-plate-nissan-skyline-r34-gt-t?variant=37829684134087&currency=AUD&utm_source=google&utm_medium=organic&utm_campaign=Advanced feed&utm_content=Carbing Radiator Cooling Panel Plate fits Nissan Skyline R34 GT-T (Coupe)&srsltid=AfmBOoonzPDKqe9NgKi5U0AkFc2XvbXETGmNWvfNcyBT5DUZagMYHg9DZ70 if you take notice it’s the same shape.  well thankfully the justjap listing has a description and it says : - Nissan Skyline R34 GT-T Coupe (M/T -07/2000) this means it’s specifically for a s2. S2’s have different front bars to s1 so that lip with the 3 holes are *probably* mounting points for the s2 bar. im not 100% sure but im almost certain it will still fit a s1 bar       
    • Everyone is too used to learning from places like HPA "how to tune" and what to expect at what point, rather than being able to see "The computer says I'm in cell with Row = 8, column =4, and I can see my fuel is lean, so lets add more" Everyone wants "real units", which helps for someone picking it up for the first time and seeing how bad the tune is if they're not used to touching it.   However, I think for most of us who want to play with it, you're 100% right, we're only needing to learn about it for OUR CAR. Which makes it great, and we don't need to care what the real values are, we just need to know which cell it is, that's causing the lean or rich point, or that we want more ignition timing or less. But again, everyone wants everything super you beaut and nearly self tuning, with VE maps, and a billion compensations...   Though then there's me over here when I'm doing reverse engineering work just reading data in hex format that most people couldn't work anything out from. Yet I can see what's going on.
×
×
  • Create New...