Jump to content
SAU Community

Recommended Posts

im just wondering which of these 2 dump pipes will give you more power - screamer dump pipe or split pulse dump pipe?

Im looking at getting either one which works best for my RB25 Turbocharger im using on my RB20DET engine

Ive seen heaps of companys selling split pulse pipes on EBAY etc but not many selling screamer pipes, anyone know of any companys that sell screamer pipes?

if you want it too sound horridly retarded, get a screamer...

they sound VERY bad on small turbo/pipes IMO.

Heard them on SRs and its pretty p|ssweak compared to a big turbo with an ext gate

If you exhaust is 3" then get the one that plumbs in.

There shouldnt be a performance loss if its 3" to begin with.

Correct. On an internal gated turbo, and a RB25 one at that I would say get the split pulse dump that joins back to the exhaust system. Just get one that seperates the wastegate gasses for a decent length, say 300mm if possible. Not the ones you see that seperate it for 50mm.

A screamer version, which vents it to atmo "might" make a tiny bit more but is ridiculously loud which attracts unwanted attention and is also illegal to boot.

A screamer pipe or "divorved" downpipe will always give you more power.

Whether or not you want a louder exhaust is up to you.

Back to back tests were done on a 7M-GTE (3.0 liter supra turbo) using a full 3" downpipe that replaced that replaced the cast turbo elbow and all, vs. a full 3" downpipe with a divorced wastegate or screamer pipe as you call it.

The result was a gain of 22 wheel horsepower from just the screamer pipe. This was done on a bone stock motor with only a cat back and an air filter + the 2 aforementioned downpipes.

Pretty big difference if you ask me.

you'll only have a gain if the exhaust is restrictive enough that you loose power.

There are a few cars the come to mind that have been tested with/without the atmo gate (on bigger cars) and there is no loss.

mind you this is using 4" exhausts and stuff. But for a small turbo setup that obviously flows a lot less... should b arite

  • 1 month later...

screamer pipes are somewhat illegal, anyonet hat thinks that this noise is tops, well drive ur car to a racetrack or drag strip. Put it on, and go for a hoon, then take it off again and drive home. On a street car i beleive it is a stupid idea. :D

have a nice legal streetable car. be it mostly legal. hehe

peace out, yeahhhhhhhhhhhhhhhh

Back to back tests were done on a 7M-GTE (3.0 liter supra turbo) using a full 3" downpipe that replaced that replaced the cast turbo elbow and all, vs. a full 3" downpipe with a divorced wastegate or screamer pipe as you call it.

The result was a gain of 22 wheel horsepower from just the screamer pipe. This was done on a bone stock motor with only a cat back and an air filter + the 2 aforementioned downpipes.

Pretty big difference if you ask me.

My guess is the difference will be bugger all compared to a split dump pipe, not a open dump like you suggested.

For example, A CES dump pipe. That would have been a much better comparison.

screamer pipes are somewhat illegal, anyonet hat thinks that this noise is tops, well drive ur car to a racetrack or drag strip.  Put it on, and go for a hoon, then take it off again and drive home.  On a street car i beleive it is a stupid idea. :D

have a nice legal streetable car.  be it mostly legal.  hehe

peace out, yeahhhhhhhhhhhhhhhh

i beg to differ.

My car is a daily driver and i have a screamer on my Rb20 and dont have any problems or a rep as being a hooooon.

Its all in the way you use the right foot if you ask me as i have heard some cars down here (turbo's, V8's) that are louder than my screamer pipe :D

Beauty of living somewhere like the Apple Isle where they are pretty easy going on mods and no EPA here at the mo either :(

Cheers B

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...