Jump to content
SAU Community

Recommended Posts

After so many pages of rubbish in that other thread none of the promised tests have been done with the 2 cats in question??? What a cop out

In fairness, I think SK has been extremely busy with the racing side of things. When people try to do things in their spare time its not necessarily a "cop out" if other things get in the way.

You could always organise to do the tests or are you going to cop out? :ph34r:

My offer still stands for free analysis of the substrate for platinum, rhodium and palladium content (the metals that actually catalyse the "nasties" in the exhaust gas).

If someone can get me a gram or so to Perth, I'll have some results back in a couple of days. You can then form your own opinion as to what the unit actually is and does.

Cheers

Gav

I've put one on my 33 gtst, and then did a 4 gas analyser test on it, and it was working fine.

Test was done with car purring along as low speed, making about 10kws on dyno until results stabilised.

Test unit was a Protech FLUX 2000 (ver 7.82)

HC was 0

Co was 0

C02 was 12.4%

No 861 ppm

Nox 947 ppm

AFR 14.7:1 (as indicated by test unit and also dyno)

If the cat wasnt working the HC and Co levels would have been up alot.

Also, everyone has to remember, you dont just whack a cat on a car and it magically (no pun intended!) cleans it up perfectly. Tuning has ALOT to do with it, timing as well as fueling.

On my results, the No & Nox could have come down by playing with the timing .

Also even for just basic go/no go testing , sitting on the dyno tuning it at 10:1 levels, and your eyes arnt watering and it smells clean..........

anyone who has tuned cars on a dyno can tell you what its like, that rich, without a cat.......... especially rotaries.

Gary

In fairness, I think SK has been extremely busy with the racing side of things.  When people try to do things in their spare time its not necessarily a "cop out" if other things get in the way. 

You could always organise to do the tests or are you going to cop out? :)

Send me 2 cars with the different cats and an exhaust analyser and i will do it. :rolleyes:

I will have to throughly trash the cars first to calibrate them

Fastrotor, what a champion thats what we wanted to hear, someone who had actually installed one and had it tested. I'm getting mine installed this week.

I do think that BATMBL should have done some testing himself if he wanted to start all this drama instead of just starting rumours. Anyway be good to hear if others have had em tested too.

pretty sure its irrelavent anyways..... its law that the driver/ owner of the vehicle is to fit a cat that meets emissions. .. if the results are in favour of one being more legal than the other... whats the other company going to do ... pay out ppls EPA fines coz a cat that doesnt comply or reemburst them for a product they bought from them? ..... highly doubtful for either suggestions

my 2c

If you took this cat and put it on a factory setup that was all working correctly, then it will work fine.

My point was that you cant just whack any cat on a car thats running a bad tune, ie not at stoic at low power (read dead o2 sensor etc) and expect the emissions to be perfect, tuning of the motor (in the case of aftermarket) , and general condition of it all play a large part for the cat to give valid results (read legal).

Gary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My take on gg2 48mm, 54mm, 58mm, and 62mm compressor map for same size compressor vs gg1 : All gg2 only outflow gg1 above 20 psi. As all g gen 2 surge line at lower left of comp map move to the right, all gg2 sacrifice spool vs same size gg1, surge line move to the right worst for 54mm gg2. So for same size compressor if you want best response, use gg1, if you want max hp at >20psi use gg2 but you will be laggier vs same size gg1. Max compressor efficiency drops to max 75% on all gg2 vs max 76%-80% of same size gg1. Iirc lower efficiency means hotter iat less dense air so lower hp at same operating point of comp map. Also curious why gg2 is mapped to lower max rpm vs same size gg1 (only 48mm size both gg1 gg2 mapped to same rpm) : 54mm gg1 165,000 rpm  vs  gg2 160,000 rpm. 58mm gg1 150,000 rpm vs gg2 140,000rpm. 62mm gg1 145,000 rpm vs gg2 140,000 rpm. If gg2 can safely spin to gg1 rpm then they can flow a bit more than as mapped. Good thing that all gg 2 interchange compressor and turbine housings with same size gg 1. So gg1 owners can buy gg2 chra only if planning to boost >20psi.
    • My stuff is all with Shannon's, granted, I don't really have imports I'm driving on the road, however, I've had multiple cars at the same time with them. Presently we have the Landcruiser on laid up cover, Sarah's Kluger on full cover, and the house insured. About 18 months ago Sarah wrote her Subaru Liberty GTB off, insured with Shannon's, and the payout, and buy back of the wreck was super quick. In 2020 we had the VF Commodore totalled in a major hailstorm. Storm was on the Saturday, I called on the Sunday and lodged it, vehicle was towed on Tuesday night, assessment team called on Wednesday to say it was a total loss and get payout details, money was in the bank on Thursday morning. Have had a few other claims both at fault, and not at fault, over the years, and never had an issue with them.   Funnily enough, they're also the cheapest insurer I find for things like Sarah's Kluger.   I will say I'm less impressed dealing with them lately around "the experience", as a lot of their staff that you deal with aren't car enthusiasts. Shannon's has a much more main stream feel ever since they decided to become "big corporate", laid a heap of staff off, and then hired a bunch of non enthusiasts. At the same time they've been making a push to be less "call us and we'll personally have someone who cares help" to "hey, this computer can do stuff for you" and are trying to get more square pegs to fit round holes. (That's just the vibe I get from them). Again, have had no issues with claims with them, but get a bit of a "less personal" feel from them.
    • A thing I wasn’t happy with with enthusiast was during the initial phone call they told me they’d insure it for 130k but needed photos.   I then sent them photos and they told me $80k as there were other cars either similar modifications available for around that price, I told them to send me the links to said cars so that I can buy them. i then sent the modification list with prices of the parts (no labor) and the price then came to 115k, which is still shy of the 130 that was agreed in the initial phone call 
    • Ask me a bit later this week before payday
    • I agree that delayed payment probably isn't the most suitable solution. It seems a solid complete transaction would be best. As I wouldn't be using this sale as a line of credit that would typically earn interest, we can probably arrange a much cleaner single transaction deal. I can do $92.52 today. Would you prefer EFT, or Cash on Pickup?  😛
×
×
  • Create New...