Jump to content
SAU Community

Recommended Posts

after 6 years of jealosy and yearning for my liner...i finally got it...but theres 1 problem ...my bloody driveway is too steep...scraped the bottom of the lip when trying to get it down the driveway ...now my baby has to sit out in the cold :)

I think its time to get the construction crew in to fix up the driveway...

anybody know any quick fixes to get the car down a steep drivway?...

if so, where do i get the materials to solve the problem....??

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/
Share on other sites

Yeh thats what I was going to sugest, planks of wood... work a treat. if they dont work.. then your driveway must be reaaaaaaaaly steep!!

welcome to the car owning side of SAU mate, it was about 4 yrs before I bought my r32 :)

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1548968
Share on other sites

sledge hammer :)

but in all seriousness, I have to use planks of wood. if you go to your local bunnings, and buy some offcut 2x4 preferreably 2 bits 1m in length, and lay them down in the gutter.

I only drive my car on the weekend, so it'd not too much hassle, but it'd drive me nuts doing it everyday. If you leave em there, some little pricks might take em.

cheers

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549063
Share on other sites

buy a sheet of that thick checker plate alluminium (Bunnings Dural has them).

Lay that across the front of your driveway, use a hammer drill to drill into the concrete, and use some bolts to bolt the alluminium down. If council complains, unbolt and remove... Then replace when they're gone... :D

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549525
Share on other sites

Thanks for the suggestions guys, ill give the planks of wood a go for now.....its almost impossible to go in on an angle because its such a small driveway, its not the initial gutter im having problems with its the flat bit just before it enters the garage...basically from the gutter its flat, then it goes down on about a 35-40 degree angle then its flat again ..its the bottom section i had probs with...

I'll stick pics up soon, but its pretty much stock looking sII with stock rims ....(next purchase)

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549681
Share on other sites

Need to go side way down.. used to happen to my ex-line with 400R front bar everyday (steep driveway). Just remember to let 1 front wheel reach the ground first then the other.

If still impossible, cheapest way is get a long timber and trim it suit ur driveway. I've seen few tyre shops use this way for customers with LOW cars.

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549916
Share on other sites

IMG_2486.jpg

IMG_2500.jpg

My precious...

Still needs some pretty rims....

I should take it out for a proper fotoshoot when i get them...

Anyway ...thanks for looking ...

ill get a foto of the driveway to explain my dilema properly when theres light...

oh yeah...those halogen lights...is it illegal for me to drive with them on?

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1551863
Share on other sites

at my old place my parents bought a sedan that was quite low, couldnt get over the edge going down to the driveway, within a couple of weeks they got construction people in, they jackhammered the concrete down and relaid half of the driveway so it was a smooth angle lol

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1552129
Share on other sites

Huge thread (do a search for Driveway Problems) about driveway problems when I first got my Skyline (well after I lowered it :))... I have one bloody steep driveway and if it weren't for the planks of wood, my front bar would be no more :)

Pros for the wood:

1) They are very very cheap, use offcuts from anywhere

2) Quite light and not too hard to setup

Cons for the wood:

1) Not good in the rain

2) Gets bloody annoying when they start to rot away

3) Depending on your road surface, it will start to destroy itself.

My next plan is to get some steel drainage vents (maybe 2m x 1m) which I can mount on top of the driveway as stated above in a previous post. Not only will this get rid of most of the cons, but will also make a nice addition to my shoddy driveway :D

Just some thoughts...

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1564870
Share on other sites

Thanks for the suggestions guys, but the real problem isnt entering the driveway from the road, its at the bottom of the driveway. *see attatched* Ive tried reversing it in to no avail.. Close, but no cigar. Anyway, i think the only option is to tear up the driveway and build a new one.

THe red bits on the images indicate where the front would hit if i drove it down front first or reversed it in.

driveway1.jpg

driveway2.jpg

driveway3.jpg

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1575619
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...