Jump to content
SAU Community

R32 Gtst Whiteline & Bilstein Suspension


Sydneykid

Recommended Posts

i just got a front pair of these shocks revalved for stiffer springs etc, and they are AMAZING.

ive had japanese coilovers (tanabe) before, ive borrowed my mates cheap and nasty HSDs and now ive got bilsteins, they are so much better than anything else ive had.

both more comfortable and handle heaps better

cant wait to take em out to the track!

Edited by salad
Link to comment
Share on other sites

  • 2 weeks later...

Hi sydneykid

im interested in these and can i have sum prices inc shipping to melbourne PM me..

-Front & Rear Springs (im looking to lower my car only 25mm front and rear coz i have 19inch" rims and any lower it will rub. so would u supply lower 25mm springs?)

-Front Bilstein & Rear Bilstein Shocks

cheers

bill

Link to comment
Share on other sites

SK i have lowered my car quiet abit...

Center of rim to gaurd on both front and rear is 295mm, and im not exaggerating at all lol

I am goin to grab a few bits off you to go with some whiteline stuff i have (mainly after some traction so adjustin the camber as much as i can), is bein that low going to damage anythin (apart from my kit and exhaust.. hahaha)??? I noticed better handlin when it was 10-15mm higher but i prefer the low look.

Link to comment
Share on other sites

SK i have lowered my car quiet abit...

Center of rim to gaurd on both front and rear is 295mm, and im not exaggerating at all lol

I am goin to grab a few bits off you to go with some whiteline stuff i have (mainly after some traction so adjustin the camber as much as i can), is bein that low going to damage anythin (apart from my kit and exhaust.. hahaha)??? I noticed better handlin when it was 10-15mm higher but i prefer the low look.

Shoot, where to start............just a short list of stuf that your are risking;

1. Drive shaft breakage is possible

2. CV joints will wear very fast (they are also soaking up extra power due to the extreme angles)

3. Steering tie rods (front and rear) are under extreme loads

4. Every single bush in the front and rear suspension will wear out excessively fast

5. The strut towers will eventually crack (both front and rear) due to the lack of bump absortion

6. The rear cradle will crack around the upper and lower control arm joints also due to the lack of bump absorbtion

7. You will suffer poor traction, so it won't stop or accelerate anywhere near its potential

8. The front and rear windscreens are stressed members, so they will eventually crack as well

9. Every electronic component is being subject to higher than its design levels of NVH, so they will eventually start to fail one by one

10. Your chiropractor will make a small fortune fixing your lower back problems

That's pretty much the major items, there are quite a few minor ones of course, but I think you get the drift.

:D cheers :(

Edited by Sydneykid
Link to comment
Share on other sites

Alright Gary... whats the lowest i can be without stressing the suspension etc too much?? :O Dont tell me 330mm coz thats heaps hahaha

I use camber correction as the first measuring stick as to how much a car can be lowered. When the camber gets grossly excessive, then you know you have lowered it too far. This is what is usually needed for each height increment, note that all measurements are centre of wheel to guard;

Standard (new) height is 380 mm front and 370 mm rear

360/350 mm needs only the standard rear camber adjusters

350/340 mm needs 1 front camber kit and 1 rear camber kit

340/330 mm needs I front camber kit and 2 rear camber kits

Using that rule of thumb, 340 mm front and 330 mm rear is a low as I would go, keeping in mind that they handle best at around 350/340. So even at 340/330 you are sacrificing handling for looks.

:thumbsup: cheers :no:

Edited by Sydneykid
Link to comment
Share on other sites

SK,

will the shocks work on standard gtst springs? and just to confirm that they are height adjustable? what's the advantage of going to the whiteline springs also?

i want something that i can adjust about 20mm lower, but put back to standard if i need to

but i also want the ride to be comfortable as this car probably won't ever see track work

and finally, just confirming that the price is for a pair? so a set of 4 shocks will be around $1140?

thanks,

Warren

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...