Jump to content
SAU Community

Recommended Posts

I recently drove my friend's R32 gtst which has coilovers and a roll cage but is otherwise stock. It sits perfectly flat through corners without absolutley no body roll. I want this handling.

I'm currently running bilstein shocks with Apexi springs (which are a progressive rate spring). I've also have ARC swaybars and front and rear strut braces. Judging by pushing down on the corners of each car, my suspension is pretty much as stiff as his.

My issue is that when I put the car into a corner (on a racetrack of course), I initially get a small amount of body roll before the suspension stiffens up, which I find a bit unsettling. It makes it hard to judge where the car's limit is.

Do you think this is caused by:

a) lack of roll cage; or

b.) progressive rate springs; or

c) all of the above; or

d) other... please explain.

My current theory is that the "soft" coils of the springs are initially being compressed as I enter the corner, allowing the small amount of body roll, before load is placed onto the "harder" coils - will a linear rate springs be much of an improvement?

Cheers,

Greg

Edited by Greg
Link to comment
https://www.sau.com.au/forums/topic/85664-spot-the-difference-handling/
Share on other sites

Rather then thinking about body roll etc, throw the same rubber on each car and look at corner speed. What feels quick isnt always, and sitting perfectly flat may not be the quickest way thru a corner?!?!?!

This is just conjecture but a darty pointy car with firm suspension could feel great and resposnive, but when you load the thing up through a quick corner with undulations like most australian roads and tracks for that matter, you may find the actual corner speed is down a little.

Then again it could be a lot higher...guess im just saying dont let the seat of the pants deceive you .

And it comes back to driver comfort as well, nand how you liek th ecar to feel. Im starting to lean towards liking a slightyl firmer setup then what i currently have, though odds are i wont be able to ride kerbs etc meaning that i will be wanting to make up a lot of time elsewhere, because at the moment my cars ability to really ride kerbs means i am able to make time on soem quicker cars then me.

I've found from riding in peoples cars with roll cages it adds much more of a firm feel. But as Roy said what feels doesn't always mean faster (lap times). Are all your other stiffening bits the same? (struts/sway bars/bushes etc?)

Could it be your wheel/tyre setup too? (i.e. lower profile tyres on your mates car?) There have been a few people around that complain about having the tyre compress before their suspension does (when they have hard suspension but high profile tyres).

As Roy posted, the feel is irrelevant, it's how much grip it has that determines how fast it is. Generally speaking a softer spring rate gives more grip. That said, we don't use progressive rate springs in the race cars. We do use tender/helper springs to keep the main coils trapped.

I have never seen progressive front springs in a Skyline, it is quite common in the rear though. But mostly to soak up the travel in the shock. The progression is there to keep the coil trapped, not to have an initial softer spring rate.

You should check this before you jump to the conclusion that it is the progressive rate that is causing the initial vagueness. Firstly check that you actually have progressive springs in the front (unlikely). Then have a look under the car (on ramps with the weight on the wheels) and see if there are any of the progressive coils not sitting on top of one another. That will tell you if there is in fact any progression at all in the dynamic spring rate.

:huh: cheers :)

The roll cage will also add weight...

And the other thing, potentially your subconsous could make you think you can go round coners safer because you have a cage around you, like, even if you come off, you wont die kinda thing, strange how the mind works.

Thanks for the replies everyone :)

I am going purely off the in seat feel, not corner speed. In some ways the feel is more important to me as my car rarely sees the track.

The tyres I'm running are 205/60/15 so there is a distinct possibility that the sidewalls are flexing before the suspension. I'll borrow some lower profile rubber to test this theory.

My front springs are definitely progressive. I will check if any of the progressive coils aren't touching each other tomorrow in the light. Thanks for your help :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You have found the problem. The wire from the switch to the HB is shorted to earth. Now you have to physically find it and replace it. It won't be the switch, although following the steps above (and yes, where you ask, that is the light switch on the RHS of the binnacle) will rule it out for sure. Or not, if perhaps the switch has melted. But there's no route to earth inside the switch, so I can't see how it would.
    • I did read your post, a few times actually.    Done. Followed this step. [Negative probe should be on the cars chassis. Positive on the wire.]   Did this partially.. now that im reading this over, i only unplugged the LED lights. [Start as said above by unplugging everything (unplug the lights, and switches.] When you are talking about the switch, you're talking about the knob thing on the right side in the drivers seat right? If so, i need to take that apart?  [Now at the switch, there is a wire from the fuse, to the switch, so out your positive on that terminal. It should read open circuit. If it reads something, especially a stupid low value, the short is somewhere between the fuse and the switch.] At this point are you referring to the connector by the headlights?  [If that's fine, now put the positive probe on the wire that goes to the headlight (at the switch plug). If it reads stupid low, the fault is from the switch, to the headlight.] Did this. I can confirm that the LED lights aren't the issue [Another quick test, is take the whole LED light setup from the left, and plug it into the right side, does it still blow the fuse? If you put the right hand side led light setup on the left hand side wiring, does the left hand side wiring now blow?  If the blowing fuse swaps from right to left doing this, your LED lights are the issue.]
    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
×
×
  • Create New...