Jump to content
SAU Community

Recommended Posts

Have been eyeing off a 'unichip' for the 33t (air + exhaust done).

However, is there a reason why I could not put in an 'emanage' box instead (and possibly the other bits later on)? It would seem to be a considerably cheaper option... too good to be true? I am not after massive power or tunablity, just a bit more zing.

Why a 'chiptorque' over a 'unichip' over an 'emanage'? Anyone got info/ideas?

Link to comment
https://www.sau.com.au/forums/topic/8598-emanage-uni-chip-torque/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

  • 1 month later...

nah thats fine... im not scared of it i just cant understand why more ppl dont use it.

the package im thinking of getting is $650 delivered from Japan

so did u get much of a gain ed?

you can use greddy's MAP sensor so once your AFM maxes out, the emanage takes over using the MAP sensor....not sure if unichip does that...

Also if you buy the e01 boost controller you can tune emanage via the e-01's screen and you can then data-log, save maps etc onto SD cards via the e-01.

I will be going this path :D

So there is no boost control function (even just a basic set and forget type) on the emanage box without going to the hand controller and screen?

+ 1 for the emanage on MAP and AFM

+ 1 for the unichip on the boost control

What about number of points for mapping? Both about the same?

ed,

I have heard some people grumbling about the emanage being a new product....not properly sorted yet......give em a couple of years...

You are obviously happy with yours, what could they change and upgrade anyway? Have you had any problems at all? What about installers and tuners, any blank looks when you fronted up (or was install and tune the same mob)?

I don't have a boost controller in my car, but then again, it's a stock turbo with full exhaust and stock cooler...

I'm peaking at JUST under 9psi...nothing to worry about there...

For the people who say give it a few years, they obviously don't know how much the japs test things before releasing on the market. There are a few things wrong with the emanage, but this is more of a document error, like the manual does not mention what the grey wire is....it's for TPS...

It was install and tune at the same place....although I AM thinking about going to a different place with my ignition harness install.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 馃槕. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
  • Create New...