Jump to content
SAU Community

Recommended Posts

Hey guys,

I got a prob with my front passenger rim on my 33. i thought the tyre somewhere had a leak as the tyre leaks air over about a month b4 i need to constantly reinflate it, so im always topping it up. i got it all checked out thinking it was the rubber, but they found a hairline crack in the actual rim.

I have 18" ROH Drift R's on the car, and i dont really want to replace that 1 rim which will prob cost 500 bucks, but it looks like i have no choice, it must be fixed or it will always continue to leak.

Is it possible to like get a tube put in just that wheel to fix it, as these type of wheels are tubeless..if thats the case id much rather pay 40 bucks than 500.

any advice would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/
Share on other sites

you can get it tubed at your local tyre place should be no dramas however i would be concerned of the safety of the rim itself if its cracked.

it could be unsafe and expand more or crack more at high speeds, that would be fatal, especially on the front

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1565224
Share on other sites

um iam pretty shore they dont make tubes for 16-17-18s coz they low profile, could be wrong about 16s but others iam shore off, just get some reall good glue n tank the tyre look 4 where air is comeing out n GLUE it, but i would fix or get new 1 if u wont i can get u these rim most likly.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1569968
Share on other sites

i would advise against the tube idea even if you can find one for your wheel as they are not the safest things going around (excuse the punt)

as someone suggested best thing is to get it repaired by wheel repairers.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1570307
Share on other sites

I got the wheel checked out at an ally repairer, the wheel is f***ed. the crack is too close to where the spoke meets the inner part of the rim so the only option is a new rim. but the rim is $280 so its not too bad..i was expecting them to be around 400-500 per rim.

And yes im still getting the 34. had it checked out and all looks good.

Link to comment
https://www.sau.com.au/forums/topic/86600-problem-with-rim/#findComment-1576025
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...