Jump to content
SAU Community

Stalling Car


aaronrb25det
 Share

Recommended Posts

i was sitting at the lights today when my car suddenly droped from idle-800rpm to a near stall only to correct itself instantly. i took off and drove about 100metres when it suddenly did the same thing,but this time whilst driving. since then it has done it several times. it doesnt sound like it is dropping a cylinder,and only looses power or nearly stalls for a second before returning to normal. the car is an r33 s1.5 det. any ideas?? :D

Link to comment
Share on other sites

could be coils or plugs..sounds like something electrical....afm also...or een crank angle sensor....try the chea stuff first or take it to a workshop if your lazy....or if u do stuff your self find someone with same car and swap coils over and see if it still does....if still does it tr afm....and the crank angle sensor u will probably need a shop to do anyway...

Link to comment
Share on other sites

Maybe if it had a distributor and coil it could posibly be leads or coil. However you have an individual coilpack for each cylinder. Id be looking at 'Cas' or something in the fuel system, faulty 'fuel pump', when was the last time your fuel filter was changed?

Link to comment
Share on other sites

i just changed the plugs a month ago to ngk bkr5eix-11 re-gaped to 0.8. I have changed the fuel filter about three months ago, and fuel hose. the bov is a GFB atmospheric vented valve, but ive got a HKS EIDS, to control the rich spike. ive noticed since i have changed the plugs it misses the slightest bit when idling.

Link to comment
Share on other sites

mine was running like shit and nearly stalling cuz of an o2 sensor. It could be heaps of shit. Anyone or any performance mech will just keep swapping or fixing shit till they figure it out. Just take it to an EFI diagnostic workshop and they will figure it out quicker and cheaper. Then take it to your performance mech to be fixed or do it yourself. That's what i did

Link to comment
Share on other sites

busted o2 wont make it stall, try stock bov. the bov is venting air the computer is expecting to have 100 units of air but your bov vents the majority of that air to atmosphere so it only has 20 units of air in the system so it adds fuel to match 100 units of air and stalls cos the mixture is off the planet. atmo bov = stall

Link to comment
Share on other sites

My S14 had a similar problem.

Mine turned out to be the wiring to the AFM.

basically, the AFM plug, the cable that goes off it, when my car is idling fine, if I touched the wire or moved it in a certain direction, the car would stall.

I did the cheap option and found a position where it wouldn't stall and taped it to there.

it's not the bov or it would happen when you are COMMING to a stop after venting the bov.

and you have that HKS doobie anyway..

start your car, open bonnet, move the AFM around, move the cable from the AFM plug around..

see if any of that makes your car stall.

good luck

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...