Jump to content
SAU Community

Recommended Posts

Hi everyone, quick question about my climate control unit. When it's on 18C (manual setting) it blows cold air, all good, but when i turn the dial to raise the temp it starts blowing hot air i.e. on 19C and above it's like the heater is on. So I can be freezing or cooking, no in between. I'm guessing it's stuffed, does anyone elses do this? Is it likely to be the unit in the dash thats all bad (something electrical perhaps) or could it be anything else before I spend the $350 I was quoted for another dash unit?

Thanks

Edited by deano_33
Link to comment
https://www.sau.com.au/forums/topic/86667-climate-control-problem/
Share on other sites

Check the little pipe that sucks air in from the dash to check the temp. On the '33 its a little circle grille near the ashtray (from memory). Not sure where it is on the stag yet. But make sure its not blocked or bent etc as it will misread temperatures.

Does that make sense?

Update: Got another climate control unit from wreckers ($350), didn't fit, different plugs on the back, same number of pins but just slightly different so don't fit. I guess the S1 and S2 stageas are different there. Wrecker is going to try to find one from a S2, don't fancy my chances though. Might have to try Nissan, can't imagine what it would cost......

Had a look at the temp sensor (to the left of the steering column?), seems OK but I don't think that would be the problem seeing as the problem is the same in auto or manual mode?

Hmm, might have to live with it for a while.

Edited by deano_33

My Stagea does exactly the same thing. I just assumed that it might have been sensing that the cabin temp was already less than 19 degrees, so it actually started blowing in hot air to bring it up to that temperature. 19 degrees inside a car with no sun shining in through the windows would actually be quite cool, wouldn't it? But now that I think of it, the times that I have tried it and it has done this have actually been at night. I'll try it again tomorrow, when the outside temp is 36 degrees with 110% humidity and see what happens. Hmmmmmmm

I think the problem could be the thermistor (thermally sensitive resistor) behind the cluster surround.

Try to replace this part first and see how that goes(few dollars i assume), because if it is old it could be sensing mega wrong resistances... and also being the "control" unit of the whole climate sensing idea..

climate20ot.jpg

climate5zj.jpg

Also, it may be dusty, so give it a good blow to get dust off (insulation)

Okay Alexcim I'll have a look, thanks for going to the effort of marking the pic!

Auto/torque converter has pooed itself though in the meantime - feels like a slipping clutch in a manual and can hear metal on metal sound, not good. Getting this attended to atm.

Might be a stupid question, but have you run the diags on the climate control to see what error it comes up with ?

J

No, not a stupid question. You get it into diag mode by holding down the off button and turning the car on right? I tried it and lots of crap comes up, how do you interpret what displays on the screen?

No, not a stupid question. You get it into diag mode by holding down the off button and turning the car on right? I tried it and lots of crap comes up, how do you interpret what displays on the screen?

Cool,

Have a look at page 31 of this doc, it's probably the same as the R33 (fingers crossed).

J

skyline_book.pdf

I thought that if the A/C is in Maunal, the Compressor doesn't come on unless you push the 'A/C' button.

If that is the case, if you select a temp that is lower than the outside, outside air will blow in. If you select a temp warmer than outside, the air will be diverted through the heater.

Does this sound correct?

  • 2 weeks later...

I think mine assumes it's always hot outside, I have to set it to around 25 or 26 degrees to keep myself warm...

Oh, and when adjusting stuff, how do you press the "Hot" button when the Stagea has a dial instead? Do you just turn it up to a warmer temp?

Hey, isn't there a button you can press so that it displays outside temperature?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not R7R. Meant to type R&R, obviously enough.
    • Bugger "making it look stock". I put one conventional internally fused Hella relay behind each globe. I just pulled the plugs off the back of the globes and built new loom segments with male and female plug parts to match up to the original loom and the globe, and used the original power wires to each globe coming from the switch through the original loom plug to trigger the relays. Ran a big fat (also separately fused) power wire across the front of the car to feed all the relays. It's as ugly as f**k, but it is wedged down between the headlight and battery on the RHS and the airbox and headlight on the LHS, and no-one ever looks in my engine bay, and on the odd occasion that they do I simply give no f**ks for what they think. Fully reversible - not that you'd ever want to. For f**k's sake. It's a Skyline. They made million of the bloody things. We've been crashing them into roadside furniture for 30 years now. There is a negative side effect to putting relays on the headlights. The coil current is too little to properly clean the contacts in the switches and they get blacked up and you have to open them up every couple of years and clean them manually. I have 25 years of experience on this point.
    • I was poking through the R34 wiring diagrams vs R33 and noticed that the R34 has proper headlight relays while the R33 is like the R32 and sends full headlight power through the headlight switch. I'm not afraid of wiring but I really would like to do this in a way that looks OEM (clipping into open positions on the OEM relay box) and also unlike the factory wiring which interlocks the high beam and low beam on the halogen series 1 GTR headlights I want to make it such that turning on the high beams keeps the low beams on as well. Any advice on how to locate the specific connectors + crimp terminals + relays I need? I was thinking one NO relay for low beams and another for combined high + low running off the factory high beam headlight connector. I don't really want to splice into a crusty old probably discontinued factory harness so fully reversible is my goal here.
    • Pretty sure they run the same engine as the Q50 hybrid which specifies 95 RON.  I ran 98 in mine for a while, but it made no difference in performance or economy, so I have been using 95 for the last few years.  I have never hit 6.0L/100km, but have returned mid to high 6 on the highway.  Being a hybrid, fuel economy is a lot more dependant on how you drive it.  At 110km/h, mine never goes into EV mode on the highway, so returns closer to 7.5L/100. urban driving can return low 8s if you are careful or over 10 if you are a bit more enthusiastic on the throttle.
    • About a quarter of what you want to do. It's only R7R, not R&dismantle&replaceparts&reassemble&R. ? It is stock. I already told you, you will NOT have broken those. It's f**king 4th gear for Christ's sake. You just chipped the teeth off.
×
×
  • Create New...