Jump to content
SAU Community

Recommended Posts

i went to my mechanic because i needed to replace my water pump. it was ment to be a $300 job (parts and labour). the night it was done i was on my way to the central coast from sydney and.......i lose all power and my car stalls on the f3???

WTF happened??? :huh:

i spent $220 to get it towed to my other mechanic. the next afternoon i was there while they stripped the motor down. timing belt was 50% of its normal thickness. little strands and belt reminence was everywhere. the head was taken off and just as i suspected...exhaust valves were f@kt! slight scratches on the top of the pistons, but they're ok.

i sent the head to the guilty mechanic and told him to replace the valves, seats and guides.

called him today and he said he's only changing the valves. thats when i called my mum...hahaha he's afraid of her! hahaha (don't laugh! you'd be too). now those three things are being changed and it's getting a port and polish too! :P

the guilty one says he's going to pay 50%

what do you guys think???

btw its an SI r33

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/
Share on other sites

I'm guessing the mechanics screwed up the timing belt while doing the water pump, which in turn caused the valves to fail. But I'm no mechanic...

In fact my mechanic friends regularly tell me that I know f**k all about f**k all. (Although when I try to tell them that the double negative in fact implies that I know everything about everything, they won't have a bar of it...).

So someone more knowlegable respond!

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1568168
Share on other sites

so how much will you be out of pocket if you pay 50% each?

if its less than $400 or so, i would say bite the bullet and pay, then stay away from that mechanic!

after all, time is money. after months spent with lawyers and in court, is it going to be worth the stress and hassle? no.

Warren.

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569458
Share on other sites

You have to take the timing belt off to change the waterpump?? isnt that strange? Most cars arent like that.. waterpump runs off the alternator belt.

Excuse my ignorance (only just got my 'line and havent had a good chance to have a sticky under the bonnet :) )

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569709
Share on other sites

$400???? more like $1500-$2000. but thats including a port and polish. hahaha. was doing maybe a little bit over 4000rpm. i have pics on my phone but i can get them onto the computer. show the damaged valves & scrapes on top of the pistons.

it feels weird not driving my car. i drive everyday sometimes have 1 day off a week or month. i miss her!!!

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569769
Share on other sites

If you can prove that it's his fault ( sometimes very hard ) then he should pay fro everything including the tow . If he replaced the timing belt it maybe esier to prove .

If he refuses you can go to fair trading .

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1571107
Share on other sites

Are you sure that is all the damage that was done? Did you ask him if he even looked at the timing belt because if he did and didnt advise you that it was old/worn he is a lame duck anyways. i'd get your scary mum ( mines scary too) to give him another rev or two and try for a better deal.

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1572207
Share on other sites

i hate dodgy mechanics but can forgive anyone for making a mistake as long as they make good 100%

if he's doing anything by way of reparation you're lucky; you're getting something from him, but it also means he accepts liability. this is good for you in case there are more problems or you want to push for more. it's a no brainer but don't piss him off now or you'll get it back in peices. as for the port and polish make sure it's being done by someone good or or it'll be worse than ever.

the dept of fair trading is your friend in this - they can't stand dodgy arseholes any more than i can. he should make good 100% but if you've agreed to the current arrangement then there's probably not much more that you can do. if you have further troubles don't do anything with this guy, call the fair trading people and tell them the whole story. they will manage the negotiation for you - it's worked for me in the past.

at this stage however don't be disappointed, it's still a good outcome.

hope things work out for you

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1572257
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
×
×
  • Create New...