Jump to content
SAU Community

Hicas Lock, Bushes And Suspension Melbourne

chugga
 Share

Recommended Posts

chugga Contributor

chugga

Posted
Posted

I am looking at getting new Bilstein or Koni suspension fitted to my r33 and thought i may as well get a HICAS lock bar and new bushes fitted at the same time.

Since i live in a country town about an hour out of Melbourne and don’t really trust any of the local mechanics my question is where in the South Eastern suburbs of Melbourne is the best place to have this done. Also where is the cheapest place to buy the parts?

Link to comment
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Talk to Andrew at Traction Tyres in Rowville.

I would recommend the Bilsteins over the Konis. You can purchase them directly from Quadrant Suspensions in Berwick. I would suggest getting matched springs at the same time.

Link to comment
Share on other sites
MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted (edited)

depends what you define as too hard. compared to some of the japanese brand coilovers, bilsteins are softer.

in general japanese coilovers are much too hard for australian roads. But i guess you need to weigh up comfort factor vs performance

i don't think bilstens are height adjustable though, and I think they will only lower it 20-30mm - though from what i've been told, any lower on a skyline and you start to mess up wheel alignment.

Edited by MerlinTheHapyPig
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Fake ARP bolts?

      By GTSBoy · Posted

      Meh. I "see" a typo above, that should have been "sell".
    • joshuaho96
      Nismo copper mix twin “pull” pedal height engagement

      By joshuaho96 · Posted

      The clutch pedal has a procedure for adjustment. This can only be done after you are 100% sure the system is absolutely free of air bubbles. You must bleed the clutch master cylinder first, then the "separation pipe" which is the clutch damper line, then the operating cylinder as detailed in the service manual. Also, you must fully depress the clutch pedal between shifts. Just because you can't feel it grabbing does not mean the input shaft is truly decoupled from the crank. At high RPM clutch plates are vibrating and moving around, you need to give it the best possible chance of success. On the BCNR33 Nissan revises these adjustment procedures slightly but not by much: I would be careful with trying to play games with these adjustments. As for the Nismo operating cylinder they say a lot of things. In practice the twin plate clutch needs less movement on the clutch fork to disengage because the whole stackup of the flywheel + friction plates + pressure plate is much taller. Personally if you find that the clutch still disengages too high at the top of the travel I would try the Nismo operating cylinder. Make sure to follow the air bleed procedures. 
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Thank you for the links. I’m going to go with the 6pin plug you used. next step is rust treating re painting dash support bar and steering column then the 6pin cradle plug when it arrives in the mail.
    • soviet_merlin
      Nismo copper mix twin “pull” pedal height engagement

      By soviet_merlin · Posted

      I don't how much the car makes a difference or whether it is just a question of gearbox and clutch. On mine it's fine. Pull type Nismo coppermix twin (standard, not competition) on the 5 speed in my Stagea. OEM slave cylinder. Bite point is a few cm off the very bottom of the pedal. Clutch pedal all the way down to put in gear, and when heading off at the lights, there's a tiny bit of nothing and then it starts biting. And fully engaged before the pedal is all the way released. There's a bit of play at the top where the pedal does nothing anymore. Are you in Australia @ck_chino? If you are set on using a Nismo slave cylinder I have one new-in-box at home. Ordered it together with the clutch but didn't get it fitted. We can work something out if you want it
    • Butters
      Nismo copper mix twin “pull” pedal height engagement

      By Butters · Posted

      I am using a pull nismo coppermix twin in an r34 getrag box, had both the standard slave and  then the nismo one. Adjusted pedal to get bite point how I wanted , it is on the higher side, but would fully disengage past half way down.  I also read that the nismo slave won't work but I had no issues with the stroke, might become one later as clutch wears but 2+ years of happy motoring so far.  Take the above as one input only, specially as my setup is a bit unique in that I am using an S15 clutch master , cefiro clutch pedal, custom braided clutch line. Lots of variables at play. 
×
×
  • Create New...