Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

i dont have dyno info,

but dont put on a pod without a heat shield, you will definately lose power if its judt ditting there in the hot engine bay.

stock airbox with panel filter and cold air pickup pipe is usually the most effective value for money

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-1576497
Share on other sites

  • 1 year later...
is there a difference b/n the gtst and the gtr stock box? in the r33 especially.

no. I run over 250rwkw.

Wack in a hi-flow panel filter and u will be set. I was convinced that unless u have a sealed box...ur just wasting time. Mine was loud and annoying...also a cop magent...stock box is quiet...and stealth.

I use a Trust Panel filter...works a treat. Dunno how much they cost but a K&N would also be fine.

Although I'm designing a new snorkel for the stock box...we be finished in a few weeks...will post pics. But its runnign fine as is right now.

KJ

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820094
Share on other sites

Hi there,

I did it on the dyno and absolutely NO difference. 254 rwkw power runs - stock airbox with K&N flat panel filter one run, then we removed the top of the airbox and flat panel filter so NO RESTRICTION WHATSOEVER and the same 254 rwkw power output - both runs done with the BONNET UP so no temp differences either.

The turbo is 2835pros kit so has fabricated aluminium turbo intake pipe which mates up with the stock airbox.

Around these power levels pods are a waste of time/money unless you like to hear the turbo/blow off valve - and in a lot of cases poeple will see a decrease in power due to the engine sucking hotter air.

Cheers

Edited by gtst25
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820218
Share on other sites

it would be ok having the pod sitting behind the front bar low to the ground? thats what i got and it's barely even dirty after 1 year, then again i never travel on dirt/gravel/sand roads, the only thing i do is avoid puddles or where theres to much water build up on the road. Sometimes the sounds gets very annoying and I wish i still had my airbox

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820279
Share on other sites

it would be even better having the open top type filters sticking low and just behind one of your front bar slots. In a S2 R33 with front bar (stock) after doing FMIC it is possible.

people have had issues with direct mount pods like this...too much air at higher speeds. They needed to baffel it to stop issues at 80+ kmph.

That being said..the gain ur gonna get..hmm not too much...stick with stock, get a decent filter, protect ur engine from crap and avoid another defect, oh an piss of they stupid whoosh sound..lol.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820493
Share on other sites

thats good to hear. especially as i've just ordered a apexi panel through kudos motorsports:P .

always wondered if its possible to do a CAI on the stock box. is this what your trying to achieve chris? any one else done this? pics would indeed be helpful :no:

andz 69: i guess it dependes on how much power they're running (which i havent a clue about). we are talking performance benefits at power levels of bout 200-300kws though

Edited by Basti
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820527
Share on other sites

I pulled off the pods and got a hold of an airbox and k&n filter simply because,

it's my daily driver (don't want to risk defect),

Pods are illegal in NSW and can't be engineered unless fully enclosed(too much stuffing around),

heatsoak in traffic.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820530
Share on other sites

personally I'm not convinced of the pod style installs where they just sit in the bay. I have done this to a few cars an recently just returned them to stock which better filters and intake pipes.

As long as an air filter and box is properly sized for an application, the lost airflow will be very minimal. I haves een some1 do actual testing but cant find the link.

If ur worried build a new lid for ur stock box and feed more air into it with a new snorkel...looks stock. In fact thats what I'm doing.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820576
Share on other sites

My 2 cents

1. Air Box fanboy here....just look at the mines GTR

2. Pods are really only useful IMO when there isnt room for an airbox or it isnt suitable for plumbing.

3. I fail to see how a pod on a intercooled car will effect the inlet temps inside the cylinders....maybe a poofteenth of a degree once its passed through the intercooler? I can understand sucking in 15 degree air compared to 50 degree air will differentiate as the intercooler can only do so much in the amount of time it has an air molecule going through it, but with the forward acceleration of the car colder air from infront of the car should go into the pod, and I doubt that a majority of the hot air from the engine bay will get into the pod as it will most likely go out the top of the engine bay and over your window / into your vents etc....

the air that actually hits parts of the motor etc will bounce proportionally to the parts it hits.....

Therefore I fail to see air that is being slammed into the front of a vehicle travelling at XXX km/h when it has little velocity before it hits the car will have less of a chance to get into your air intake than the air that is rushing to the back of your engine bay and out of any gap it can find (as mentioned between ur bonnet etc)

my 2 cents of keyboard warrioring at 1.30am :no:

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820622
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi everyone, Apologies in advance if this feels like a topic covered multiple times. I'm only asking because some of the old topics I found are missing images now. I'm in the process of getting a manual boost controller (BC). Nothing fancy, just getting a manual one for now as I don't plan to go crazy with it and would not go over 10 PSI. My car is not jacked up on boost steroids to do crazy numbers. I want to understand the OEM setup of the boost solenoid and vacuum lines on the R34 GTT so I know what needs to be changed when I do install the BC. I sketched the current setup to the best I could see and it's on the diagram attached. If the boost controller 'Wastegate Arrow' goes from nipple 1 to 2. My understanding is that the red vacuum line's "F" connector-end should be connected to BC nipple #2? Nipple #1 is meant to have the "pressure source" so what vacuum line would that be? Is it the green vacuum line?  From what I have read here, the OEM boost solenoid is not used at this point. So that can come out and then I can just plug the nipple that usually connects to the blue vacuum line?  So would the final setup look something like this?   Thanks in advance. I don't want to already be knee-deep into pulling out vacuum lines before understanding this. I'm a noob when it comes to boost setups so trying to learn as I go.
    • Initial/early bite is a feature of.....generic pads. Things that work cold. Just put Bendix Ultimate in it. If you don't like them, it's only $3.50 wasted and an hour to change them. I've been using Intima SR, and they seem to be a good performance pad. Street friendly and able to take at least a little beating.
    • This is my first post after registering.. I hope i can find useful resources on this forum. Great forum. 
    • As I implied in my post, I have NO idea what the were. But in case I didn't make it clear, the way they performed was brilliant; whatever the brand was. I think it was the compound that made the difference. And if they were Bendix, then sign me up, I want another set. I did drive down mount Ousley (just outside of the Gong) a few times, and they showed no untowards performance.   Its not the low dust that I am looking for NOW. At the time I needed low dust, but now I have no issues with dust but want the initial/early bite of the pads that were used. Yeah, the early cold squeal may of been due to a missing shim or such.  And to repeat, its not the low dust I am seeking, its the initial bite of the pads and increase in bite as  the warmed up during each breaking. As soon as I let off, I don't remember the breaks being extra sticky if I used them again soon after. But I also did not test that theory.   Thanks for the recommendation, But I would prefer to choose something specifically with the behaviour I described.   I assume that they didn't use the default compound off the shelf, as we discussed the dust issue at length. And the early squeal when cold, I have seen the sound is more of an issue with some pad compounds. Mostly ceramic, which also are said to produce less dust.
    • Well, in 2007 he must have been charging about $1800 an hour. He only looked at the car for 5 minutes. And another 4 to write the report wrong, and another minute to correct it. Mind you, this was for a car that was: Stock engine, fmic (hole in drivers guard), all alloy intake and custom air box, 3 inch turbo back exhaust, lowered, and a set of 17" Advans (255/40/17 rear and 235/45/17 front). It was nothing crazy. The blue slipper wanted the "hole in the guard" engineered. But that was because he got the shits that I wouldn't "relocate the battery from the boot, back to the factory position in the engine bay"... In an R33 GTST...     Also for emissions, E85, and don't go wild on timing. It's amazing how the closer you get ignition timing towards max torque, the last couple of degrees really throw NOx counts right up. And for the huge increase in emissions, it's only a small increase in torque.
×
×
  • Create New...