Jump to content
SAU Community

Recommended Posts

Well I'm not even sure Chris is going to make it now (he had car problems yesterday at Phillip Island) so it looks like I'm screwed anyways. You just have to get enough compeition yourself now because Pete has blown a turbo so he's gone from Calder too.

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey Al would you sell just the tyres? As those rims might not clear my new rotors

Yep.........

For the same price :lol:

Unless you are running some ridicules callipers, these rims should clear them, as they have more clearance than the factory rims.

Im gonna try my hardest to be there!.. seeing as i could come 2nd (D) :D Can anybody confirm the passenger sessions?? i heared they were totally abolished but they are still in the sup regs info?....

question: in regards to the DB limit, how strict are they on that, in your experience??

Asking because I'm new to the track and my car runs an external gate venting to atmosphere, which obviously breaches the DB limit

thanks

Dane

Click Here For Entry List

PS. Ant - they either stuffed up what car your driving or you've been keeping secrets from us!!!!  :(

hehe, they are hopeless! they did that to me at the last sandown track day... the person who puts in the entrant car details see skyline on an entry form and automatically assume it's a GTR! :P

Yep - Mark Pether is a black R34 GTT as well - not a GTR as listed.

I don't know - I think these rex guys just like to list the RWD Skylines as GTR's so if they beat you they can feel good about themselves.

Sif a rex could beat a GTR. :P (Full race going versions with slicks not included Clayton! lol)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...