Jump to content
SAU Community

Car Wash Places


R32Skyliner
 Share

Recommended Posts

I heard that there is somewhere you can drive your car up onto a big ramp or something and get underneath so you can have a go at it with a high pressure hose. Although I'm thinking the driveway idea might be the best option as I have a steep drive, just have to get a hold of some ramps.

Link to comment
Share on other sites

I find there is usually a way to have the front end of the car hanging over the steep part of the driveway as most of them have a flat part and a ramp part. Put ure wheel just over the crest and then reverse it to get to the other half.

Make sure u chock the wheels so u dont get squashed though. Just in case ure park brake fails by some evil magics.

Link to comment
Share on other sites

Go to supercheap or some place similar. Buy a can of degreaser (worth next to nothing) spray tons of it all over the car where oil needs to be taken off. Then hit it with a high pressure spray from your local car lovers.

Done

Link to comment
Share on other sites

hummmm, alot of jacks and 4 stands, degreaser and high pressure, wouldnt be any other way to do it "cleanly" done it to mine, just the front half though, have no idea where to jack it up from the centre at the rears. (gives u about 400g of weight reduction :))

Link to comment
Share on other sites

Thanks for all the ideas guys and Rob for the offer of the ramps. I ended up borrowing some ramps off a mate who lives nearby and used our slanted driveway to get under the car. Already have a high pressure hose and some degreaser, so was able to give it a good clean. Didn't realise that some areas under there are actually grey, not black!! Anyway, came up well, so I'd recommend this technique for anyone doing the same.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...