Jump to content
SAU Community

Recommended Posts

Macka - I been once, 3 weeks after I got my car!!! On my last runs I started having the power probs I just fixed for the first time.

Don't reckon I got much out of the last session aside from the knowledge that I couldn't drive a greasy stick up a dog's you know what...

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by skyzerr33

can't tell  

the engine bay, can't isolate it seems to be plenum side but i can't tell for sure

Is it a new noise or just the fact that you are listening hard for the first time.

Cheers

Ken

Originally posted by skyzerr33

oh yeah still no pressure at the radiator cap

Troy , stop being so paranoid and worrying about the worst case scenario.

As I said on the phone , it is probably the rad cap has lost pressure and allowing the water out of the overflow.

The murky colour is because you have probably boiled the water when it stopped and it's like giving the block a hot enema , all sorts of shit will come out.

Drive it home tonight , take it easy and don't use the aircond.

Get a new cap in the morning from Auto one , Marlows , Coventry's , whatever.

It's only a cap and the same as dozens of others.

Cheers

Ken

Originally posted by gtrken

Troy , stop being so paranoid and worrying about the worst case scenario.

As I said on the phone , it is probably the rad cap has lost pressure and allowing the water out of the overflow.

The murky colour is because you have probably boiled the water when it stopped and it's like giving the block a hot enema , all sorts of shit will come out.

Drive it home tonight , take it easy and don't use the aircond.

Get a new cap in the morning from Auto one , Marlows , Coventry's , whatever.

It's only a cap and the same as dozens of others.

Cheers

Ken

fingers are crossed

driving like miss daisy all the way home and out to lumpy for the fuel pump

Ohh and drain the water , or get c red to do and stick some new coolant in.

The reason it boils is that without the cap pressure the water will boil at 100deg C

Your car should run normally at about 90 deg C and the 13 or 15 lb cap will raise the boiling point to about 120deg C.

this is why when you open the cap if it's in good nick after driving it , the water will suddenly boil , cos ya dropped the boiling point down to normal.

As yours has no pressure , it will boil easy.

Cheers

Ken

The hissing sound is probably normal pod filter induction or at the worst a vacuum line is off or split.

Just that you are looking and have suddenly heard what has been there all along.

Besides , a blown head gasket does not make a hissing noise , it causes the engine to run rough on startup ( as I said on the phone ) or blows water out of the radiator while it is running or a LOT of bubbles will appear ( some are normal )

Cheers

Ken

Originally posted by adam 32

when coolant says anti-boil - what does this actually raise the boiling point to?

it is the pressure in the radiator that stops most of the boiling.

Anti boil has an additive , like glycol or something , which raises the boiling point slightly , depending on the mix.

Cheers

ken

Originally posted by skyzerr33

sounds good to me ken

i'll stop being a worry wart till the morning. :P

Good , can I close the online free mechanical w/shop and get back to whoring before pwpt60secf arrives ??:P

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Probably a smart choice to buy one vs build, purely for the motivation part as you said! Imagine the metal dust everywhere from grinding all the steel to build one. Ha ha ha!   Also, post a photo of your garage.   Mine is below, this is where I've been cleaning and have already half filled a caged 6*4 trailer. And this is after my cleaning expedition mentioned previously... The middle normally has a car in it, but I'm dumping things in the middle as I sort through them. And poor skyline was dusty and has had the lightest few drops of rain and now it looks atrocious and needs to be dragged back out and washed thoroughly! And yes to the right is technically another bay, you really can only see 2 bays out of 3 in this picture.  
    • It's more like on average the things I see a lot of things going wrong. Yes, usually the people who reach out are the ones who are having problems but on average it feels like mechanics and tuners here aren't really competent. I swing between thinking my standards are just way too high and wondering whether people really are just this dumb. I just had the strangest 10+ reply argument on a Facebook group over someone insisting that the factory R34 GTT boost control solenoid reduces boost pressure to 5 psi when it's on and raises boost pressure to 7 psi when it's off despite showing the exact plumbing in the factory service manual and the solenoid behavior detailed in the FSM.
    • I steam cleaned my near new set of volk gtc wheels 14 years ago and farrkkked them lol. The clear coat cracked like spider webbing in several areas. Lesson learnt don't do that. 😭
    • If you don't touch the CAS, then you're fine.
    • Yeah, my moulds and seals are 32 years old now. I think I will continue to not use a pressure washer on it.
×
×
  • Create New...