Jump to content
SAU Community

My In Car Vid 9.3's @ 160 Mph Pass

keith cowie

By keith cowie,
in General Automotive Discussion

 Share

Recommended Posts

keith cowie Enthusiast

keith cowie

Posted
Posted (edited)

If you want to see my in car video of me doing my 9.4 sec pass

at 160 mph,I then went on to set a new record and win the event.

Go to the link below and download the second video down

Hope you like it

http://www.totb.co.uk/movies/

Keith

KeithPoster.jpg

Edited by keith cowie
Link to comment
https://www.sau.com.au/forums/topic/88447-my-in-car-vid-93s-160-mph-pass/
Share on other sites
keith cowie Enthusiast

keith cowie

Posted
  • Author
Posted
Congratulations Keith!

Been following your efforts for a long time on GTROC UK :D

edit: I just watched the vid, and I think you shut it down early!!!! :O  :P

Hi Merli

We were having fueling problems all day,we found that

it was a fault with 1 pump at high revs.

The EGT at the end of the runs were about 1000 degrees

this video was taken in the final and I was a good second in front

so I didn't see the point of risking my engine so yes I backed off early.

Keith

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches · Posted

      Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • GTSBoy
      AC not coming from top vents

      By GTSBoy · Posted

      What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • dbm7
      Shifting questions

      By dbm7 · Posted

      ...oops. forgot the TCU end...
    • Sleepergm
      Custom titanium intake

      By Sleepergm · Posted

      No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
×
×
  • Create New...