Jump to content
SAU Community

Recommended Posts

hey guys

my car stands

122rwkw

auto completely stock 16.1

auto

FMIC

10psi

AVCR

166.9rwkw

CES front dump pipe 15.2

Manual conversion

highflow cat

tuned at fist

170.1rwkw ( clutch slippin, was told by fist could of gone more )

back to 8psi 14.3

test and tune after 19th october <<<<<

turbosmart type 3 pb ( currently not plumb back due to autobarn f@#kin me round hang on ........ AGAIN!!!!

power fc install 19th october

Will see if i can put it back to 10psi

reason why it was put back to 8 was, it wasnt makin anymore power at 10

all times recorded were done on street tyres on 40psi

next time i go down after install of power fc will drop pressure of tyres to 25

Just gathering ppls thoughts to, what times would i be lookin at

when i get the power fc installed?

let yas know when i get it in and go down the track .

THanks

Barret

I'm guessing you drive an R33 right?

By the time you get your PFC installed and tuned, you should have something around 170-200rwkw depending on how much boost you run and depending on the dyno. I only mention the dyno because your previously quoted figures look a little on the generous side, but if all your figures have been done on the same dyno, then it's all relative so that's ok (BTW, what did FIST tune? You didn't mention that you had another programable ECU or an SAFC for example).

On street tyres, that should be good for anything from mid to high 13's (or even quicker with sticky tyres).

Good luck

what i was sayin was car completely stock ran a 16.1

the next lot of upgrades was

FMIC

10psi

AVCR

166.9rwkw

CES front dump pipe 15.2

then next lot of upgrades

Manual conversion

highflow cat

tuned at fist

170.1rwkw ( clutch slippin, was told by fist could of gone more )

back to 8psi 14.3

first tune was at mercury motorsport , didnt tune my car !

2nd was at apc, which they apperantly tweaked the ecu abit

and did a poor job on my intercooler piping

3rd was at fist, which involved change timing, changed boost, as it was all over the shop , first run on the dyno tune b4 they touched the car was only doin 116rwkw.

once they tuned the standard ECU and changed timing and boost

it did 170.1

didnt mention that i had a programmable ecu because i dont have one !

standard .

And where is WSID, im in QLD i go to Willowbank raceway

thats if WSID stands for it .

what i was sayin was car completely stock ran a 16.1

the next lot of upgrades  was

FMIC

10psi

AVCR

166.9rwkw

CES front dump pipe 15.2

then next lot of upgrades

Manual conversion

highflow cat

tuned at fist

170.1rwkw ( clutch slippin, was told by fist could of gone more )

back to 8psi 14.3

first tune was at mercury motorsport , didnt tune my car !

2nd was at apc, which they apperantly tweaked the ecu abit

and did a poor job on my intercooler piping

3rd was at fist, which involved change timing, changed boost, as it was all over the shop , first run on the dyno tune b4 they touched the car was only doin 116rwkw. 

once they tuned the standard ECU and changed timing and boost

it did 170.1

didnt mention that i had a programmable ecu because i dont have one !

standard .

And where is WSID, im in QLD  i go to Willowbank raceway

thats if WSID stands for it .

Good luck at Willowbank.

once they tuned the standard ECU and changed timing and boost

it did 170.1

didnt mention that i had a programmable ecu because i dont have one !

standard .

Don't think you can tune the Std ECU on an R33 mate...hence my earlier question.

Maybe check with the workshop and find out exactly what they did if you're curious. If the Std ECU was tunable, it kinda negates the need for the PFC then doesn't it? PFC will make a noticable difference in any case.

Good luck at Willowbank :P

yeah i might have to check what they did

cause i remember apc sayin that they could tweak the standard ecu abit

could of been something else though, who knows

whateva they did, they could of done a betta job.

let yas know what happens

thanks for the replies

  • 4 weeks later...

guys back again just got my install and tune of power fc

car is currently on 11 psi near enough with 187.6rwkw

power curve is real nice havent been able to give it a good go around

due to being wet

but next test and tune i'll be out there to see what time i can rack up

hopefully gettin into the 13's

let yas know how it goes

Barret

  • 1 month later...

Due to AFR's being real rich at 10.5, and timing a bit out from the tune at FIST

i have had my car tuned again at chiptorque ,

and needing a new o2 senser and spark plugs

got a result of 201.7rwkw on 12psi

After the tune of fist i did manage to go down the quarter and did a 14.089 at 101.69mph,

so will be good to see what happens now.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...