Jump to content
SAU Community

Engine Noise On R33

baron25

By baron25,
in General Maintenance

 Share

Recommended Posts

baron25 Proficient

baron25

Posted
Posted

Recently my engine developed this annoying rattle at 1500rpm or so. It seems to disappear once the revs climb, and it doesn't do it at idle, only in the 1500-2000 rev range. Any idea what this could be? It sounds like it's coming from the front of the motor, but i'm not sure if it's from the top or from the pulleys and belts at the base.

Link to comment
Share on other sites
ien Newbie

ien

Posted
Posted
Recently my engine developed this annoying rattle at 1500rpm or so. It seems to disappear once the revs climb, and it doesn't do it at idle, only in the 1500-2000 rev range. Any idea what this could be? It sounds like it's coming from the front of the motor, but i'm not sure if it's from the top or from the pulleys and belts at the base.

I believe that this is your timing belt idler or tensioner pulley bearings starting to show their age. My car had this exact noise in the same rev range and when I replaced the timing belt and pulleys, the noise was gone. If your car is coming up to 100 000 km then I would get them replaced pronto.

Link to comment
Share on other sites
baron25 Proficient

baron25

Posted
  • Author
Posted
I believe that this is your timing belt idler or tensioner pulley bearings starting to show their age.  My car had this exact noise in the same rev range and when I replaced the timing belt and pulleys, the noise was gone.  If your car is coming up to 100 000 km then I would get them replaced pronto.

Mine's only supposedly done 56,000km but. How would i check if it is the timing belt?

Link to comment
Share on other sites
ien Newbie

ien

Posted
Posted
Mine's only supposedly done 56,000km but. How would i check if it is the timing belt?

I got my mechanic friend to do the replacement for me, but I think the best way to check the belt is to get a mechanic to take off the cam gear cover and crank angle sensor unit to inspect the belt condition. I think in my case it was more to do with the bearings in the 2 pulleys as they sounded like a cement mixer when you spun them.

It isn't a cheap exercise to replace all these components, especially when you have labour costs to consider, so I would probably get a mechanic to check it for you to be honest. This way you won't end up replacing something that might not be broken.

I think the parts cost me about $500 and there will be a few hours labour involved. My car had come up to 100000km when I bought it so I had already factored this into the equation. My car is a 95 r33 so I think it's around the same age as yours, going from your sig.

Link to comment
Share on other sites
cme33 Apprentice

cme33

Posted
Posted

If you can get your hands on a stetescope. (kinda what docs use to listen) you'll be able to pin point the noise. Approx $15 from Autobarn... supercheap... repco ect. I've got a similar noise to what your saying and i found it's my A/C compressor bearing. It only does it between 1,500 and 2,000 RPM. It's annoying but i'd rather wait till it gets worse and buy a new one, my A/C still works fine!

Or another poss. maybe check the tension on all your belts and timing belt.

Link to comment
Share on other sites
Angry Fist Enthusiast

Angry Fist

Posted
Posted

Hi I bought my skyline about 2 weeks ago and I'm still getting used to it but I've noticed sometimes when I'm shifting up from 2nd to 3rd that theres a coarse gravely noise until i get to around about 40km/h and then things start smoothing out. I haven't noticed what rev range it occurs in. Is this normal?? or I am shifting up to early (I think it should be)?? My last car was an auto and I haven't driven manual in about 2 years?

Cheers,

AF

Link to comment
Share on other sites
Zahos Mentor

Zahos

Posted
Posted

Could be the springs on your spung centre clutch are loose...

Mine made a grinding noise b/c of a faulty clutch plate where the springs were loose. It always did it at lower revs, and most audiable in 3rd and 2nd gears.

If I changed gears to early and load it up at 1,500 rpm in 2nd or 3rd, it was very noticable...

Link to comment
Share on other sites
Angry Fist Enthusiast

Angry Fist

Posted
Posted

Damn I think you hit that right on the bulls eye...I'm guessing thats going to be a fair bill to fix.

Could be the springs on your spung centre clutch are loose...

Mine made a grinding noise b/c of a faulty clutch plate where the springs were loose. It always did it at lower revs, and most audiable in 3rd and 2nd gears.

If I changed gears to early and load it up at 1,500 rpm in 2nd or 3rd, it was very noticable...

Link to comment
Share on other sites
Zahos Mentor

Zahos

Posted
Posted

that means the clutch plate is faulty (sort of).

From what I understand, if it IS that, then it won't cause any damage, it is just an annoyance.

Cost to fix is basically replace clutch plate...

What clutch do you have?

I have a daiken exceedy organic sports clutch.

Link to comment
Share on other sites
Angry Fist Enthusiast

Angry Fist

Posted
Posted
that means the clutch plate is faulty (sort of).

From what I understand, if it IS that, then it won't cause any damage, it is just an annoyance.

Cost to fix is basically replace clutch plate...

What clutch do you have?

I have a daiken exceedy organic sports clutch.

I'm not too sure, hey? I just bought it probably just on two weeks ago now but there was no paperwork (manuals, instructions or compliance or whatever else)with it, even though I bought it at a dealer...come to think of it, I think the bastard's ripped me off since now the front right small headlight thing (the corner one, the faint ones?!) doesn't work anymore..

do you by any chance happen to know where a good reliable skyline service centre is in Syndey or where I can get keys, manuals and stuff from?

Cheers

AF

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Roy
      R32 GTS/GTST non driven wheel speed

      By Roy · Posted

      Another complicated thing is to run Z32 alloy hubs which have wheel speed sensors for ABS. You need different tie rod end, and you need new bearings on the upright etc. I did that as part of a major refresh when my front kingpin bearing flogged out., Alloy was a little lighter, runs a bigger bearing , gives a few extra mm in wheelbase as it moves the wheel forward in the arch (cant run crazy but can still get 8ish comfortably).   All in all glad I did it but was a head fark as tried it once and abandoned it the first time. sav man swung his spanners at it and got it working so using his guidance on GTR/Z32 tie rod ends etc and the required mismatch of parts was able to make it work.  Probably a 2k upgrade all said and done :(   I think the best bet is just look around your front wheel and see what you can pick up rotationally. You see old Escorts, E30s etc all get very creative with front uprights and the humble old angled alloy bracket.
    • Butters
      Garrett G-XRace Range

      By Butters · Posted

      Big claims here.  Any links up on the website ?   
    • Butters
      RB gearbox options

      By Butters · Posted

      If your HP goal is reasonable and you are not drifting. Buy a new R34 box.  If the above is not true, buy a wrecked R33 box and put a gearset in it.  CD09 are not as strong as you think and the cost of / mess around of the conversion puts you in gearset territory.    Also the deal above is awesome,, get that  
    • dbm7
      Got this r31 silhouette flood car to rebuild.

      By dbm7 · Posted

      Just got back from a little hands-on with a G58 Baron....I was thinking about this... ..best I can figure it, that pinny was tail-ended ...I didn't really think about the wiring, because all that mattered was the tank and pump cradle (I think I mentioned the pump itself I couldn't vouch for)...which didn't matter, as you said you'd be replacing the pump anyway.... ...'for some reason'....and I imagine this is the panel shop's doing... they've replaced the cradle wiring with a metre of 7-core trailer loom, and attached the loom plug (from a different car) to that. The actual cable run from the top of the pump cradle, to fuel pump harness end in boot, is maybe 60cm in length...so I've no idea why they did this... ....the connector in the boot of the pinny, is not going to help you here...because in theory, it should still be present on your car. On top of that, because they've done what they did, we have no idea which colours of the trailer cabling, have been connected to what on the fuel pump cradle (pump +/- , shield, fuel guage/low-level senders)... ...this means, best approach is to remove the pump cradle, and re-work it now ...not later. That is, if you were going to replace the pump, do it, replace the soft lines at the same time...and sort the wiring out (replace that trailer cable with the wiring loom off your old cradle)...
    • GTSBoy
      Fake ARP bolts?

      By GTSBoy · Posted

      Well, maybe not. The main feature of Chinese manufacture seems to be incredibly variable quality, coupled with an apparent willingness to find a way to see even the stuff that fails QC. So the military could still take the cream of the production run and somehow sell the "sellable but not really useable" stuff to the stupid round eyes on the other side of the world.
×
×
  • Create New...