Jump to content
SAU Community

Need Help Asap

Black.32

By Black.32,
in Car Audio & Electrical

 Share

Recommended Posts

Black.32 Explorer

Black.32

Posted
Posted

ok guys and girls im in the process of doing my install and it needs to be ready by tonight. everything is going fine except i dont know how to take off the back seat. any help would be much appreciated. i have serach but havnt had any success. i have seen the r33 rear seat remove tutorial but the r32 doesnt have many similarities.

thanks in advance

Link to comment
Share on other sites
Murry33 Experienced

Murry33

Posted
Posted

okay people will tell you to pull up and forward etc, it make take a little time and effort, but thats simply bullshit lol.

To get it out in two seconds, grab a crow-bar or a piece of strong metal at least 30cm, slide it under each corner below the seat and pull up. You'll hear it click, then just do the other side. It's easy for then on just pull it out and undo a few bolts.......i guarantee its the easiest way B)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Nismo copper mix twin “pull” pedal height engagement

      By soviet_merlin · Posted

      I don't how much the car makes a difference or whether it is just a question of gearbox and clutch. On mine it's fine. Pull type Nismo coppermix twin (standard, not competition) on the 5 speed in my Stagea. OEM slave cylinder. Bite point is a few cm off the very bottom of the pedal. Clutch pedal all the way down to put in gear, and when heading off at the lights, there's a tiny bit of nothing and then it starts biting. And fully engaged before the pedal is all the way released. There's a bit of play at the top where the pedal does nothing anymore. Are you in Australia @ck_chino? If you are set on using a Nismo slave cylinder I have one new-in-box at home. Ordered it together with the clutch but didn't get it fitted. We can work something out if you want it
    • Butters
      Nismo copper mix twin “pull” pedal height engagement

      By Butters · Posted

      I am using a pull nismo coppermix twin in an r34 getrag box, had both the standard slave and  then the nismo one. Adjusted pedal to get bite point how I wanted , it is on the higher side, but would fully disengage past half way down.  I also read that the nismo slave won't work but I had no issues with the stroke, might become one later as clutch wears but 2+ years of happy motoring so far.  Take the above as one input only, specially as my setup is a bit unique in that I am using an S15 clutch master , cefiro clutch pedal, custom braided clutch line. Lots of variables at play. 
    • dbm7
      Got this r31 silhouette flood car to rebuild.

      By dbm7 · Posted

      Oh for sure, I'm just recounting my thoughts 😎 I'm not what you've got there to fuzt with.... likely my first idea was on the money -- rebuild or replace connectors. You can get a lot of connector stuff here  -> https://www.rapidcables.com.au/ Didn't look in the boot of mine, because I replaced these when I renewed the pump (plastic of connectors had gone brittle) edit: what I used... https://www.efihardware.com/products/2120/Deutsch-DTM-Connector-Kit-6-Pin ...cheaper... https://www.ebay.com.au/itm/364900039138
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      In no way was i suggesting it’s your fault mate. The trailer cable has a plug that I removed. I will have a closer look, but I did remove the trailer wiring cable with the tow ball as I don’t need it on my silo. i have replaced the fuel pump already there’s no need to remove the cradle again I can see the wire colours from it in.
    • Roy
      R32 Pix Only

      By Roy · Posted

×
×
  • Create New...