Jump to content
SAU Community

Recommended Posts

Has anyone had to change their brake master cylinder in their 32 gtr ?

Mine is leaking and in need of replacement but iam having trouble finding a new one. Would anyone know where i could get one ?

Thanks

Tim.

Most good brake shops will be able to recondition the master cylinder for you - you will have to do without it for a few days. Approx $200 is the asking price.

Just a word of warning - insist they get the seals etc in their store BEFORE you give them anything & check they have done a GT-R one before. I got caught like that by two different shops & had to swap units between my cars.

Just made a few calls.....

ABS said they have no listing for new master cylinders or kits but they could recondition the one I have using parts and seals from other kits. This would cost about $300 to $350 but he hasnt done a GTR before and cannot guarantee it can be done.

Nissan said $620!! for a new master cylinder and

$174 for a kit.

I think i might be best to get the correct kit from nissan and get a good brake shop to recondition it. But iam not sure ??

Tim.

  • 1 month later...
If Nissan have a kit, then use that. The guys at ABS should be able to work with it.

Do you have a part number for the KIT?

It would save my life if someone can post it. The local NISSAN dealer will get it if I have that magic number.

Regards

Mark :)

Hmm, I am having problems with my Master Cylinder too at the moment. Feels like theres air in the system and the pedal is really squishy before I start the car.

I am pretty sure mine is just the seals and may just need a kit, and I can guarantee its gunna be more than $174 from Nissan in Perth :)

32 and 33 GTR are apparently different I've never had the two side by side though.

Master cylinder v air in the lines.

Air in the lines - when you put your foot on the pedal it is really mushy, but if you pump it a time or two it comes up nice and hard

Master cylinder leaking - when you put your foot on the brake and hold it, your foot sinks slowly to the floor.

Air in the lines - when you put your foot on the pedal it is really mushy, but if you pump it a time or two it comes up nice and hard

mine is like that, but it takes a damn while to come good. I mean like 45+ seconds before its normal and then throughout a drive its good

I should have said, air in the lines is very easy to fix, you just need to bleed the brakes. There should be a thread on here about how to do it.

If it hasnt been done for a while run a whole bottle through first make sure its clean and bubble free.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...