Jump to content
SAU Community

Rb25det Parts And More!

400GTST
 Share

Recommended Posts

400GTST Enthusiast

400GTST

Posted
Posted (edited)

R33 RB25DET S1(i think it fits rb20's as well) X-FORCE Dump/front pipe 3 inch stainless steel with oxy sensor hole(2 weeks old) $200

RB25DET S1 Cast exhaust manifold with head shield $50 SOLD

RB25DET S1 Plenum top with fittings,most bolts and gaskets. $80

RB25DET S1 Airflow meter, Mesh removed from one side. $100

RB25DET S1 Airbox to turbo pipe, with bov plumb back hose and oil breather line. $100

RB25DET S1 L-Shape crossover pipe with bov mount $50

RB25DET S1 oil cap $10

RB25DET S1 Turbo Heat sheild $15

RB25DET S1 Standard fuel press reg and assorted fuel lines and hoses $50

RB25DET S1 Right angle pipe off turbo $50 SOLD

RB25DET S1 2 x Standard cast dump pipe $20

R33 GTST Front strut brace Polished bar with red ends.1 Week old. Selling due to high mount turbo being put on.$90.

CA18DET(180sx) Stock intercooler and piping $50

Various intercooler pipes 2 1/2 inch $50

T25G Turbo off ca18 or sr20 With actuator and right angle pipe and standard dump

Oil seals a bit worn out. Perfect for high flow rebuild. $100

Pm for more details. Will post most parts at buyers expense.

post-20794-1128054301.jpg

post-20794-1128054351.jpg

post-20794-1128054385.jpg

post-20794-1128054449.jpg

post-20794-1128054483.jpg

post-20794-1128054520.jpg

post-20794-1128054585.jpg

post-20794-1128054621.jpg

post-20794-1128054655.jpg

post-20794-1128054712.jpg

post-20794-1128054771.jpg

post-20794-1128054808.jpg

post-20794-1128054851.jpg

post-20794-1128054885.jpg

post-20794-1128054917.jpg

Edited by 400GTST
Link to comment
https://www.sau.com.au/forums/topic/89408-rb25det-parts-and-more/
Share on other sites
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...