Jump to content
SAU Community

Washing Engine Bits


chugga
 Share

Recommended Posts

i had something like that in my old car.

Somehow water had gotten in the bits where the spark plugs go.

We used a high pressure air hose thingy to get it all out and off she went again.

hi,

my girlfriend thought it might be a good idea to hose down her engine

now when she starts it, it the engine shakes as if its miss firing

how do i fix this?.

she has an R33 skyline the same as mine.

Link to comment
Share on other sites

It sounds like its missing, hence the weird sound. Could definately be a fouled plug (alternatively, perhaps there is still water around the coil). Seems to be very common when people wash their GTS-t engine bays without sufficient care.

Link to comment
Share on other sites

take your coils out and use high pressure air to blow the water out of the spark plug hole, if you dont have a compressor then just use some kind of thin fabric to soak up all of the water around it. put it all back together after making sure your coils are dry too, then should run fine after that.

Edited by SECUR1TY
Link to comment
Share on other sites

Chicks and maintenance on a vehicle makes me laugh. Reminds me of a mates girlfriend who cleaned his motorbike and put tyre shine on the wheels, not just the sides but the whole tyre. First corner he came to he washed out sideways. She will never live that down.

Link to comment
Share on other sites

u could not believe how much trouble me and a mate had with our r33 after high pressuring the engine bay, his alarm went off and my wipers got possed by the devil.

keep goign off by it self. just let the egine dry. start it or a air gun and blow it out good.

leave it to dry...should do the trick after over night.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Meh. I "see" a typo above, that should have been "sell".
    • The clutch pedal has a procedure for adjustment. This can only be done after you are 100% sure the system is absolutely free of air bubbles. You must bleed the clutch master cylinder first, then the "separation pipe" which is the clutch damper line, then the operating cylinder as detailed in the service manual. Also, you must fully depress the clutch pedal between shifts. Just because you can't feel it grabbing does not mean the input shaft is truly decoupled from the crank. At high RPM clutch plates are vibrating and moving around, you need to give it the best possible chance of success. On the BCNR33 Nissan revises these adjustment procedures slightly but not by much: I would be careful with trying to play games with these adjustments. As for the Nismo operating cylinder they say a lot of things. In practice the twin plate clutch needs less movement on the clutch fork to disengage because the whole stackup of the flywheel + friction plates + pressure plate is much taller. Personally if you find that the clutch still disengages too high at the top of the travel I would try the Nismo operating cylinder. Make sure to follow the air bleed procedures. 
    • Thank you for the links. I’m going to go with the 6pin plug you used. next step is rust treating re painting dash support bar and steering column then the 6pin cradle plug when it arrives in the mail.
    • I don't how much the car makes a difference or whether it is just a question of gearbox and clutch. On mine it's fine. Pull type Nismo coppermix twin (standard, not competition) on the 5 speed in my Stagea. OEM slave cylinder. Bite point is a few cm off the very bottom of the pedal. Clutch pedal all the way down to put in gear, and when heading off at the lights, there's a tiny bit of nothing and then it starts biting. And fully engaged before the pedal is all the way released. There's a bit of play at the top where the pedal does nothing anymore. Are you in Australia @ck_chino? If you are set on using a Nismo slave cylinder I have one new-in-box at home. Ordered it together with the clutch but didn't get it fitted. We can work something out if you want it
    • I am using a pull nismo coppermix twin in an r34 getrag box, had both the standard slave and  then the nismo one. Adjusted pedal to get bite point how I wanted , it is on the higher side, but would fully disengage past half way down.  I also read that the nismo slave won't work but I had no issues with the stroke, might become one later as clutch wears but 2+ years of happy motoring so far.  Take the above as one input only, specially as my setup is a bit unique in that I am using an S15 clutch master , cefiro clutch pedal, custom braided clutch line. Lots of variables at play. 
×
×
  • Create New...