Jump to content
SAU Community

Recommended Posts

If u hav the spare cash, Blitz i-color, first full color boost controller on the market, it has combined the Blitz Power ID with the Blitz SBC and given it a full color interface display unit...mind-blowing display, if u want something that holds boost well, GReddy Profec B Spec2 or Profec E-01. I've heard the turbosmart ones hold boost well too. The avc-r is not bad, but definitely not the best in holding boost. However, it's easy to use and pretty comprehensive.

BLITZ SBC I-D III

Best Value for Money IMO....

Probably the best on the market next to the New I- Colour but there is around a $500 Price Differance

SBC I-D III -- $ Around 600 Brand New

I-Colour -- $ Around 1K Brand New but has shitloads more Features....

Obviously almost everyone is going to recomend the EBC that they have in their own cars...so I'll do the same :(

I've got a GReddy Profec B Spec II and it does the job for me. It might not have all the snazzy displays of some other EBC's, but it does have most of the functionality that you'll ever need (3 boost settings, gain function, peak hold display, boost warning etc). And most importantly, it holds boost fairly constant through the rev range.

Good value for money :)

Thanks. I tried a search but it wasn't going to be quick...

38 Pages on EBC's :\

I'm leaning towards the boost controller kit for the PFC as it's cheap and has pretty much the same functionality as the AVC-R.

I might add the thing I liked about the Profec B II is the add-on feature you can get with that boost button thingo for the steering wheels :)

I'm going to be using the Turbosmart E-Boost 2 - Apparently, features +++ and controls the extarnal gates NO Problem... So, reviews and peoples experience will be the determining factor I think.... Good Luck in choosing... there is heaps out there.

I second the Jaycar. Its the cheapest and the best.

Make sure you get one that uses the solenoid to completely block off the air flow to the actuator, they work the best in terms of reducing wastegate creep to the lowest possible.

At the moment I have one of those Turbosmart bleed valves..

Would it be an advantage if I got myself an Electronic type boost controller?

If so which would be most suitable Apexi AVC-R, Greddy Profec B II?

I have an Apexi PFC so I was thinking the Apexi AVC-R..

Depends on how much boost you eventually want to run. Above about 1.2 bar you probably should go for a dual solenoid setup - in which case I would recommend the Blitz ID III.

Below that a single solenoid Blitz or an Apexi will do a good job.

Best prices are either from Nengun or Greenline etc.

Gentalman i have an E boost 2 fitted to my r33 with small mods

ok let me say when it was installed it was set too high and i did not like it

but an e mail to turbo smart and no s$% i had a phone call less than 5mins later asking wat was wrong

he told me how to set it

now it is the BEST thing i own, no really it is a boost gauge as well

i can do minor adjustment from my cabin and it holds boost well,

very well + dont need to spend $$$$$ on gauge and they are AUSTRALIAN THEY ARE THE BEST END OF STORY

mine cost me $915 installed but i dont think its needs a dyno straight away it has a 1 to 100 setting 30 is 10psi 40 is 14 psi and so on but only on the 40 psi model.

I am on 30 now 10psi but i can stress enough without taking you for a wrap how user friendly they are

ps i dont work for turbo smart but when you find a good product you tell everyone i think + we should have a thread about good mods so we all no wat is good to buy

How much for the Eboost and how much for a jaycar kit?

I just paid $745 (E-Boost 2)and I'll be doing a self install. So, we'll see how it goes... The Jaycar kit, all up plus an hour or 2 of your time cost about <$150 - although, does it have a "BLING" display like the E-Boost (2)?? :angry:

Also, you'll need a boost gauge and that can be anywhere from $80-$$$$$.

Edited by QUIKBLADE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
×
×
  • Create New...