Jump to content
SAU Community

Recommended Posts

hey guys battery was playing up but is new so i got a brand new alternator, i no the regulator is internal, put it in and checked with the multimeter and is putting out 17.6v on idle. this doesnt sound right, i thought 14.6v was normal. any advice will be greatly appreciated. thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/90777-alternator-charge-rate/
Share on other sites

17.6V is waaaay too high, assuming your meter is accurate. Anything in the region of 14 to 14.5V is normal. Most likely your regulator is stuffed, but best get things checked.

Edit: make sure all your connections are correct.

Edited by SteveL

meter is 100%, this made car blow black smoke really bad[ fuel] ive had no luck with this car for the 18 months ive owned it, had to do everything a number of times cause everything i get for it is wrong. might as well keep spending on it cause its nearly brand new now. thanks SteveL

It's your alternator regulator, get it replaced. You will start frying very expensive electronics before too long at 17V. I know someone who had around 17V in his old crappy Magna, and things started dying one at a time. Headlight bulbs, dash lights, dashboard, stereo head unit. The stereo was the last thing to go for some reason, and it was only then that he decided to see what might be wrong with the electrics! I guess he had his priorities right, who needs a working fuel gauge as long as you have music :P

the alternator is brand new(genuine nissan), only put it in and run it for 20 seconds. voltage regulator is internal. spoke to the electrician today and he said maybe faulty, or a fuseable link could be stuffed. ill have a bit of a play but if i cant find it ill get him to fix it. thanks for the reply JimX

jimx i doesnt neccesarly mean your reg is shot alts on new cars use a battery sense wire this tells the regulator the conditon of the batty pull the two pin plug off at the reg check with a test light check to see if it has battery sense at one of the pins if no then thats where i would start lookin try and find where that battery sense has gone

also check to see if you have warning light by putting the earth clip onto pos and probing the two pin plug you should get a dull glow if you check in side the car for a batt light being on do all this with the key on

cheers hope that helps

As per the nissan manual, voltages should be up around 14 something volts when cold then drop to 13 something volts once warm.

How much was the alternator from Nissan?

Its possible they supplied the incorrect one? Unsure if that would cause overcharging or not. :(

Edited by Cubes

paid $330 for the alternator. its fixed now. checked the plug and it had 12.2 pos on one side, 12.2 neg on the other. bridged them and the charge light came on. put the plug back on and started the car and is now charging at 14.2v. ill just keep an eye on it, thanks for the feed back guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...