Jump to content
SAU Community

Recommended Posts

Go and see Japanese Motor Sport, they are experts with skylines bot standard and locked diff. They will also probably be the best and cheapest way to get it fixed if it's busted.

The have both standard and aftermarket diffs in stock.

Mechanicals are wierd in their operation.

You've really got to see a pic of one to understand.

Basically when you apply power (and there is a power difference between the wheels and the motor) the force will push out some rods or spindles things that lock the wheels together.

That puk puk puk puk noise that you hear when going around slow tight corners under power is the inside wheel skipping/spining accross the road.

Remember that the inside wheel will be wanting to spin as fast as the outside wheel but has a shorter distance to travel cause your urning a corner, so the wheel will actaully spin a bit.

Mechanical are good fro drift work, great for track work, and amazing for drags. Basically the most traction you'll get from a 2wd car is a straight line.

Some LSD will swap the power from one wheel to the next which will cause fishtailing - not a good thing. with a mechanical there is always a 50/50 split, even when you start spining the wheels.

God I hope that makes sense ????

J

I think thats your wheels spinning XrSiSt

Thats perfectly normal..

I raced an R33 with a locked Diff.. he wrecked me.. I just kept spinning the wheels (with 255s on the ass) My car had heaps more power then his, but he was able to put his less power car to the ground better.

I say.. if you want a straight line car, and soley want it for dragging... stick with the locker..

But for everyday use, and just a few squirts here and there, the stock LSD item is sufficient ;)

The diff is probably different BUT..

When I had the VS V8 IRS Manual Commodore the diff first started to open wheel a little especially in the wet.

Then idling around corners with no accelerator slow speeds it felt like the diff was a slight locker. i.e the arse end would wobble a bit.

It started to get worse where if i was not perfectly in a straight line and riding the clutch waiting for traffic rolling back then creeping forward a little the diff would make the car have that slight wobble in the arse end like it was a locker and there was also like a slight click clunk type noise when the arse end was wobbling.

Then it all of a sudden was an open wheeler (occasional twin) then the bearings started making a loud grrrrrrrrrrrr on acceleration.

Apparently the bearings where buggered and also the cones which are like the clutch packs or what ever they are..

Replaced everything cost $1000 and the diff was tight enough that on full lock in a servo with the shinny surface the inside wheel would chirp.

Diff then whinned for a little after it was rebuild ?!?

He told me the diff had to be lapped in or somthing.

Anyway it did. whine stopped just before i sold the car thank god...

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I suppose that's true. Barring almost any situation, I'll never sell so what the market does is kind of irrelevant to me. It's possible I'd make most of my money back. That spreadsheet I mentioned? Maybe I could make back more than what the car's total costs thus far are, but the parts and all that is possibly a different story... Thanks for reading. It was certainly a good moment and just makes the ties to the car that much stronger. It's exciting that the option will be there to bring it over, however I have some plans with a shop that may end up keeping the car there longer, not sure. Coupled with the fact I want to move there and haven't solidified any path yet. So in a way, it feels like I'm in a limbo state that is uncertain; time will tell.
    • No worries, everything worked out in the end. I just wanted to make the point that it doesn't matter where it comes from (I.E Australia), it can be broken or improperly built. I would still purchase from these companies in the future. B2R - Not certain how that finished, this was on a car I wired a few things and street tuned. I know the owner ended up shipping the motor back to Australia for investigation. Hopefully some of it is covered under warranty.  Turbosmart - I always pressure test everything that goes on my car. It's a habit from my career in oil and gas. I run two 40mm's and both had major leaks from the actuator to exhaust portion through the shaft. I returned both, they shipped me back two and one was leaking and the other had a 38mm top (40mm gate with 38mm actuator cap, no idea how that happens). Eventually after a lot of back and forth I found myself with two non-leaking gates. I believe this happens a lot more then people would like to believe but you would never know if you don't pressure test them prior to installation. Crank Motorsport - Issued a full refund and let me keep the seat rails. I turned them into scrap metal for other projects. GKTech - Shipped me out a replacement and asked that I modify it as per my idea and that they would do the same for a future revision. ATP - Can just needed a large shim to bolt up properly.  Haltech - They started an actual proper Beta channel for firmware's a few months back and stopped using the general public for testing. I'm now much happier.  Speedtek - f**k Speedtek. I would love to watch them burn.     
    • I've got a Turbosmart wastegate, ATP catch can, many GK Tech parts and Haltech everything. Everything's been perfect, sorry to hear your experience wasn't the same
    • The only high-power RB I've personally seen go pop after running for all of an hour on a dyno was built by B2R, while being remotely tuned by B2R. The only wastegates I've ever had leak like a sieve, return, still leak, return and get shipped back the wrong ones were from Turbosmart. The only final drive that I've ever purchased that were unusable, twice... were from Speedtek. The only seat mounts that I've ever purchased that placed the seats in the door frame were from Crank Motorsport. The only poorly designed parts that I had the manufacturer confirm should have been designed as per what I mentioned were from GKTech. The only ECU I've had firmware updates consistently break things are Haltech. The only catch can I've purchased that didn't fit in its advertised spot was from ATP. So forth and so on... Moral of the story, doesn't matter where it's from. Do your research beforehand and stick with products and companies you've trusted in the past.    @joshuaho96 If you want it done right, do it yourself.
    • Something coarse-ish. 180 is good.
×
×
  • Create New...