Jump to content
SAU Community

Recommended Posts

Go and see Japanese Motor Sport, they are experts with skylines bot standard and locked diff. They will also probably be the best and cheapest way to get it fixed if it's busted.

The have both standard and aftermarket diffs in stock.

Mechanicals are wierd in their operation.

You've really got to see a pic of one to understand.

Basically when you apply power (and there is a power difference between the wheels and the motor) the force will push out some rods or spindles things that lock the wheels together.

That puk puk puk puk noise that you hear when going around slow tight corners under power is the inside wheel skipping/spining accross the road.

Remember that the inside wheel will be wanting to spin as fast as the outside wheel but has a shorter distance to travel cause your urning a corner, so the wheel will actaully spin a bit.

Mechanical are good fro drift work, great for track work, and amazing for drags. Basically the most traction you'll get from a 2wd car is a straight line.

Some LSD will swap the power from one wheel to the next which will cause fishtailing - not a good thing. with a mechanical there is always a 50/50 split, even when you start spining the wheels.

God I hope that makes sense ????

J

I think thats your wheels spinning XrSiSt

Thats perfectly normal..

I raced an R33 with a locked Diff.. he wrecked me.. I just kept spinning the wheels (with 255s on the ass) My car had heaps more power then his, but he was able to put his less power car to the ground better.

I say.. if you want a straight line car, and soley want it for dragging... stick with the locker..

But for everyday use, and just a few squirts here and there, the stock LSD item is sufficient ;)

The diff is probably different BUT..

When I had the VS V8 IRS Manual Commodore the diff first started to open wheel a little especially in the wet.

Then idling around corners with no accelerator slow speeds it felt like the diff was a slight locker. i.e the arse end would wobble a bit.

It started to get worse where if i was not perfectly in a straight line and riding the clutch waiting for traffic rolling back then creeping forward a little the diff would make the car have that slight wobble in the arse end like it was a locker and there was also like a slight click clunk type noise when the arse end was wobbling.

Then it all of a sudden was an open wheeler (occasional twin) then the bearings started making a loud grrrrrrrrrrrr on acceleration.

Apparently the bearings where buggered and also the cones which are like the clutch packs or what ever they are..

Replaced everything cost $1000 and the diff was tight enough that on full lock in a servo with the shinny surface the inside wheel would chirp.

Diff then whinned for a little after it was rebuild ?!?

He told me the diff had to be lapped in or somthing.

Anyway it did. whine stopped just before i sold the car thank god...

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
    • I would suggest equally difficult to find, perhaps edging to the SR. Turkey has almost exclusively Euro market cars, some Korean, few Japanese other than pedestrian shite. I guess they're probably losing the fight against Chinese shit like we are now too. I would vote for a BMW V8, found in a 540i in a wrecking yard somewhere in Deutschland (or possibly Albania).
    • A CigWeld EasyWeld 130 can be had from ebay for $360 delivered. Good for 0.6 to 6mm, which would be fine for my requirements. I guess that on top of that you would need to buy a regulator, hoses and wire. I already have gloves and an auto-darkening mask. How is the gas bottle charged? Do you rent it then pay for top ups?
    • RB20 being an option from factory would mean no custom parts or fabrication required, just have to collect the right bits. Probably would be the easiest option I reckon for a motor swap. How common are SR20s vs RBs in Turkey?
×
×
  • Create New...