Jump to content
SAU Community

Dyno Day - Power Tune Australia

mac30

By mac30,
in Events Archive

 Share

Recommended Posts

TommO Grand Master

TommO

Posted
Posted

Yeah I went out there about 10:30am and unfortunately it was postponed due to wet weather (unable to put cars on rollers?)

Oh well, looked like a nice workshop and will keep an ear out for the next day :D

Cheers,

Tommo.

mac30 Collaborator

mac30

Posted
  • Author
Posted

Apologies for all who showed up and and couldnt have there cars on the dyno. Understand that some of u guys had travelled from quite a distance.

Unfortunatelly I was there as well hoping it still be on and didnt have a chance to post on forum that it was cancelled, all we managed to do is put a sign up in front of workshop that it was postponed.

The owner have decided to have it again on the 6th November so hopefully u guys will be there and for those who couldnt make it last week here is your chance.

Beer Baron Grand Master

Beer Baron

Posted
Posted

it's pretty poor form to cancel on the day with no way to tell anyone. there were a number of people i know of who went quite some distance to get there and i would be surprised if any of them will want to go back.

Blitz Grand Master

Blitz

Posted
Posted

The trick is, if you are going to use SAU to advertise your event, have the courtesy to tell people if the event is cancelled so they dont drive from the Northern Beaches all the way there to find out its postponed.

mac30 Collaborator

mac30

Posted
  • Author
Posted

Fully understand how people might feel. I travelled all the way from cronulla as well, sleeping only 4hrs and got there all excited hoping the event will eventually happen. I take full responsibility for not been able to communicate earlier that the event was cancelled and have taken all comments and advise seriously for future postings.

Once again I and many others where disapointed, personally seeing the good turn out, variety of cars and the friendly atmosphere.

  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • The Bogan
      NC MX5

      By The Bogan · Posted

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...