Jump to content
SAU Community

Recommended Posts

if its shaky den it's wheel balance..

I had the exact same problem, took it in for a wheel balance (obvious solution)

When they jacked it up at the shop i had a look and the dick before me had put spacers in (to push the rims out), which was the cause of my tyre hitting the wheel guard at every little bump, but when i took the spacer off i noticed there was no hub locater. The lack of a hub locater meant that the rim had play between it and the hub. Machined up two of these little bad boys and problem fixed =no shake

This will only be a prob (i think) if you have aftermarket rims and if the guy that had the car before you was a dick, or the dodgey dealer you bought your car from was also a dick (had these problems)

Cheers

Or it could be as simple as a wheel balance -- easier fix too

Link to comment
https://www.sau.com.au/forums/topic/91458-shaky-at-100km/#findComment-1667531
Share on other sites

Wheel alignment will fix how the car travels down the road. If you take your hands off the wheel and the car continues to track straight then the wheels are aligned.

If there are vibrations, then it is probably (with exceptions like mentioned above) going to be wheels out of balance. Most balancing centres can only balance 16-17" rims. I tried to have some 18"s balance and had to have them driven across town to find a big enough balancer. Without casting dispersions upon the guys that did the balance, they may have taken a short cut with your balance if they didn't have the right equipment.

Link to comment
https://www.sau.com.au/forums/topic/91458-shaky-at-100km/#findComment-1671760
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...