Jump to content
SAU Community

Recommended Posts

Hey guys just wanted to see if anyone has had this problem with there cefiros

When i get to 1/4 tank left in my car it starts acting like shit

spluttering, poor acceleration and just generally runs like poo

I fill up the tank and straight away its fine again

was think it could either be

1. Dirty muddy crap in the bottom of fuel tank

2. My fuel pump is spittin the dummy and cant maitain pressure with less than 1/4 tank

3. its just my imagination and its not really happening

let us know what you guys think, or let me know if you have had similar problems

thanks

Link to comment
https://www.sau.com.au/forums/topic/91479-dirty-fueltank/
Share on other sites

yeah i think i got the same here - its not the fuel pump (nippon denso 600hp) but when i go around corners on 1/3 tank it does what you have described. i was thinking of a surge tank but i would rather fix the prioblem - could be crap in the bottom.

interested to find out if anyone has fixed this problem

shaun

Link to comment
https://www.sau.com.au/forums/topic/91479-dirty-fueltank/#findComment-1648921
Share on other sites

Odds are it is just surging, it may have something to do with the position of the fuel pump inside the tank that is causing "pick up" issues under 1/3 or 1.4 tank.......

Easiest way to fi the problem s to keep it above half :)

My car never see's under half as it starts to surge at about 1/3 (this is whilst on the track drifting though, i don't drive it on the street so i can't comment on that)

PS: I have recently fitted a new tank (clean) and new pump so my surging is not caused by crap in the bottom.

Link to comment
https://www.sau.com.au/forums/topic/91479-dirty-fueltank/#findComment-1652983
Share on other sites

Well i got adventurious last night and decided to pop the pump and everything out

low and behold was a fist full of dirt floating in my fuel tank.

Someone obviously didnt like the previous owner in japan

i ended up having to drop the whole tank out and scrub the whole inside of the tank as it was full of mud and rust

it still aint perfect so im going to have to look for a new tank eventually

but for the moment it is alot better and actually runs normally below 1/4 tank

Link to comment
https://www.sau.com.au/forums/topic/91479-dirty-fueltank/#findComment-1660413
Share on other sites

I believe the R32 and S13 fuel tanks are the same.......you just need to change the fuel filler neck.

Hope that helps you find one. (make sure you take dimensions etc before you buy to ensure i am correct.......i COULD be wrong, it has been known to happen, sometimes lol)

Thanks for that man

Hopefully the S13 at the wreckers tank is in alright condition

is good to be able to finally drive my car on the limit without it shittin up on me

Link to comment
https://www.sau.com.au/forums/topic/91479-dirty-fueltank/#findComment-1662541
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is there a diameter difference in the stock to Nismo? If so, the weight alone won't be indicative when comparing flywheels of the same diameter, since the radius of the flywheel acts on the moment of inertia with a square factor, where as mass is linear. Roughly going from a 4.5kg flywheel with radius 20cm, to a 9kg flywheel with radius 14cm would see them act the same. This calc is just here to act as a brief numbers comparison and reflects no actual RB flywheel diameters etc. it also assumes even weight distribution (thickness) throughout.
    • It seems this could be due to a restructure/team direction change... Or... You're working with a different category of vehicle... Or you've decided you'd rather be able to play with your own cars again...   I'm hoping the latter...
    • had 4 weeks off over xmas and well did some stuff to the shed and BRZ, well short of is I don't work full time in supercars anymore as of yesterday.........
    • Did you get any down time over Christmas, or have you had any since to play with this? Or have you given up and are trying to get yourself a second hand V8SC instead?
    • A random thought I had just before I hit "Submit on this post". If brake fluid, in a container in my garage that has never been opened goes bad after 18 months, why can I leave it in my car for 24 months in an "unsealed container"... Secondly, some other digging, and brake fluid manufacturers seem to be saying 5 year shelf life... Me thinks there line on 18 months for an unsealed bottle is pretty much horse shit marketing spin. Kind of like how if you drive a car and don't run a turbo timer your turbo and motor will die horribly...   Where I started on this though... Someone (me) started down a bit of a rabbit hole, I don't quite have the proper equipment to do Equilibrium Reflux boiling per the proper test standards. I did a little digging on YouTube, and this was the first video I found on someone attempting to "just boil it". This video isn't overly scientific, as we don't have a known reference for his test either. Inaccuracy in his equipment could have him reaching the 460 to 470f boiling point range in reality. In the video, using a laser temp gun, he claims his Dot3 that's been open in his florida garage for over a year gets to about 420 to 430 fahrenheit (215 to 221c) Doing some googling, I located an MSDS for that specific oil, and from new, it claims a dry boiling point of 460 to 470f. Unfortunately they don't list a wet boiling point for us to see how far it degraded toward its "wet" point. While watching it I was thinking "I wonder what the flash point is..." turns out its only 480f for that specific brake fluid....   As for testing the oil's resistance, I might not be able to accurately do that unfortunately. Resistance level will be quite a LOT higher than my system can read I suspect based on some research. However, I might be able to do it by measuring the current when I apply a specific voltage. I won't have an actual water % value, but I'll have some values I can compare between the multitude of fluids. I'll run some vague calculations later and see if I should be able to read any reliable amount of current. These calcs will be based on some values I've found for other oils, and see how close I'll need my terminals together. From memory I can get down to 1pA accuracy on the DMM. I don't think my IOT Power Tester has any better resolution.    
×
×
  • Create New...