Jump to content
SAU Community

Recommended Posts

I was gonna ask the same question, im looking at an ECU for my R32 and someone told me about e-manage for Skylines. Tuning it requires a laptop and rough knowledge of fuel-air ratios so leave that up to a dyno tuner. But they come relatively programmed to start with so you can plug it in and drive away with a pre-programmed setting. Fuel-air ratio will be a bit better, engine timing a little greater so its not a bad thing. But for it to be fully sick get it dyno tuned. I rekn your looking at a 10kw boost from it after a dyno tune.

Link to comment
https://www.sau.com.au/forums/topic/92089-e-manage-on-r33/#findComment-1660501
Share on other sites

the emanage is a piggyback and an expensive one at that, if you are looking at spending that much you should either consider a remap or aftermarket stand alone.

have a read of emanage vs aftermarket stand alone powerfc

http://www.skylinesaustralia.com/forums/in...showtopic=92051

Link to comment
https://www.sau.com.au/forums/topic/92089-e-manage-on-r33/#findComment-1661134
Share on other sites

I'm using an Emanage at the moment in my S1 R33, it's not tuned yet though. I haven't had any problems with it after installing it, haven't noticed any power gains either. The car just runs as if it isn't there, until you either get it tuned or try to do a rough tune yourself with the adjustment dials on the front.

"But my mum says I'm cool."

Link to comment
https://www.sau.com.au/forums/topic/92089-e-manage-on-r33/#findComment-1662574
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, you failed to pay your washer cover subscription and BMW have revoked your access.
    • Haha thanks Lith,  So it's currently working quite well and the torque reduction is setup and working phenomenal. It also got a custom torque convertor from All Fast in WA. Stall speed somewhere around 5500rpm unlocked but still with the lockup. The car went back onto the dyno after a 3yr hiatus (even with the dbw, and other mods completed in this time) managed to make ~515kw at all 4 hubs. Sean setup the Torque reduction which now sounds awesome and working well. We setup adjustable torque controlled launch control aswell.  Man what a feature. Especially when drag racing on street tyres I Managed to get out to the drags late last year and tick a huge bucket list item off of running mine and the cars first 9. Car went a 9.98 @142 Still had the young fellas car seat in the back aswell.  This was on 255/40/17 Nankang AR-1.  Currently the Turbolamik is still completing it's own torque calcs and managing shift times from there. Unfortunately emtrons can export is still a little restrictive to export the ecu calculated torque just yet but I have recently been suggested a work around that I just haven't had a chance to trial yet.     
    • Yeah its bad eh. Ey! Watch your mouth. Yep, spot on. The rear's are always gone too though from brake checking. I had them perilously close to a tree that we had taken down. I think the tree peeps may have taken it. Either for a trophy, or accidentally.  
    • f**kin' yikes! That insulation is the shittest stuff I have ever seen. You need to do an insurance job on that f**ker, pronto. WRT to the washer cover, I would have said that there'd have to be some at a wrecker, then remembered that it's a BMW, and reasoned that every single wrecked one would have been tailgating and so the front end would be trashed.
×
×
  • Create New...