Jump to content
SAU Community

Recommended Posts

is there anywhere in brisbane that do side skirts for 32 gtr's. I've called dmd the image but they said they only do the two types on their website and i'm not interested as they are way too over the top.

I was after something simple like the one in this photo. I can't remember where i found this photo, i was hoping it was off this forum so they could let me know where they got it.

thanx

post-20345-1130149270.jpg

Link to comment
https://www.sau.com.au/forums/topic/92287-sides-skirts/
Share on other sites

I was looking at getting the Veilside body kit (front bar and side skirts) from "180sx" on this forum. However, I dont feel comfident enough to actually buy from this guy considering he quoted me $600 including postage, yet bodykit designers and makers here in brisbane are quoting me $1800 including rear bar and fitting.

Link to comment
https://www.sau.com.au/forums/topic/92287-sides-skirts/#findComment-1664875
Share on other sites

  3LIT3 FORS3 said:
It looks very similar to the standard s2 side skirt I think. are you sure it's not the standard unit.

nah, i'm pretty sure it's not. I've never seen it before. It's subtle but definately different, i think

Link to comment
https://www.sau.com.au/forums/topic/92287-sides-skirts/#findComment-1667778
Share on other sites

  Haro said:
The side skirts on that GTR came with it when it was imported. I dont know what brand they are tho.

The car is for sale also (minus, roll cage, crazy wing, clear tailights and a few other bits and pieces)

damn it, oh well.

Has anyone else noticed 32 GTR's comin ova with these skirts???

Link to comment
https://www.sau.com.au/forums/topic/92287-sides-skirts/#findComment-1670485
Share on other sites

  3LIT3 FORS3 said:
You could try some cardboard and stick it on top of the original skirt. Then paint the cardboard. It would look pretty sik!

sorry George just kidding!

if you can get away with holding your car together with sticky tape then i guess i can :D

-------------------------------------------------

sum1 buy these plates -

http://www.skylinesaustralia.com/forums/in...showtopic=92599

Link to comment
https://www.sau.com.au/forums/topic/92287-sides-skirts/#findComment-1672644
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
×
×
  • Create New...