Jump to content
SAU Community

Recommended Posts

I think the first thing to check is if it is dual 2 or dual 4 ohm voice coils coz a dual four will only run at two or eight ohms thus a monobloc and a dual two will only run at 1 or 4 so probably look at a two channel and bridge it.

Just out of curiosity how much are you guys paying for the suitable jaycar amps just so i know what sort of budget you are shopping with.

W3s are hot man especially in the ported box but don't feel bad about giving it 400-500 wrms they love it as long as its clean power trust me.

Run mine in the shop (JB HiFi) in qld off a 500/1 and it is tight as. If you really want to hear it sing try a jl e1400D (if its a dual 4) and you'll never go back. If its a dual two ohm (less likely) go to JB and check the prices on coustic 600S two channels for comparison to jaycar stuff they are good for 350wrms bridged and sound great on subs especially for under $300.

Link to comment
https://www.sau.com.au/forums/topic/93516-what-amp-to-use/#findComment-1688784
Share on other sites

just to clear it up a dual 2 ohm sub will present a 4 ohm load if you run the two coils in series or 1 ohm if you run the two coils in parallel.

Same principle as wiring two single voice coil subs you can only double or half the impedance with each addition so two four ohm subs wired together will run at 2 or 8.

So the jaycar two channels are okay if the sub has two ohm coils, the audiobahn A8000T will give give 400rms at 4 ohm or 800 rms at two ohm. Mass_iv has also got dual 2 ohm subs as both subs would be wired in series to four ohms and the two subs would be wired in parallel to the amp to bring it back to two.

Link to comment
https://www.sau.com.au/forums/topic/93516-what-amp-to-use/#findComment-1693499
Share on other sites

  • 2 weeks later...
go to jaycar and get their new line of monoblocks, set you around ~$800

should be able to crunk out 800 watts RMS @ 2 Ohms, if your sub is dual 4 ohm

thats overkill for that sub, but in the future if you get a sub with higher power requirements it would be useful.

Link to comment
https://www.sau.com.au/forums/topic/93516-what-amp-to-use/#findComment-1729316
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, but no. You need to keep the mating surfaces bare (ie the flat faces where the caliper and upright pads touch the dogbone) and also the internal threads will remain bare (unless there are no internal threads - do they use nuts on all the bolts?). So you can slow down obvious external corrosion, but not all of it. Anodising would be required to provide decent protection to the alloy, but I'm not actually sure if you should anodise something that is all about the strength. Anodising does reduce strength significantly. Like, up to 50% on some alloys for high thickness coating.
    • Thanks   does painting on aluminium work or stop them from corroding?
    • 'Sgot nothing to do with them being Japanese. The climate in the north of Japan has similarities to the UK - the cars are made in the knowledge that they have snow and salt, and they rot there. Cars made in the US rot like buggery in the US. British cars have always rotted regardless of the weather. They will rot indoors in a climate controlled bubble! The brackets are not unsafe yet, but they will get that way. They may well corrode where the bolt threads are in contact and the bolts could just jump out without warning.
    • So unsafe would you say now?   little bit of has come off, guess road salt is a nightmare for Japanese car. Mx5 here have a well known issue or rotting 
    • Dissimilar metal corrosion. Aluminium is less noble than steel/iron, and will corrode preferentially when in contact with it and a conductive solution (ie, wet road salt). Tends to suggest that those brackets should be made in steel for a shitty climate like the UK.
×
×
  • Create New...