Jump to content
SAU Community

A31 Cefiro Parts List!


BenA31
 Share

Recommended Posts

^ Just to clear this up for ppl refering to this thread... there are 2 different sets of brake setups stock on the cefiro's so don't just assume this is the same for you.

Edited by skypy12
Link to comment
Share on other sites

thanks.

found out its actually R33 gts rear calipers as they are vented.

thanks anyways

so the rotors for an rb20det ceffy are r33 aswell? or sr20det ones? or ......

also it is noted that 4pot r32gtst calipers with na r33 rotors are a break upgrade for 4 stud ........any body got any more info on this is it a straight swap? ....can u use gtr calipers on them ? ....how much bigger are the na rotors?

Edited by Resin
Link to comment
Share on other sites

  • 4 weeks later...

Does anyone know if the Air conditioning system is the same as R32's and/or S13's? Or, are there parts that fit and some that don't, for example does the condenser fit but the compressor not?

Edited by rb25ceffy
Link to comment
Share on other sites

  • 3 weeks later...
Anyone know if there are any compatable alternators available on the local market, for the ceffies.

I used a second hand one off a r32 rb20det, worked till it died too.

have you tried looking at the specs of the rb30 one? (mounting points and charge etc) might work...

UPDATE: checked this with my mate who is building up a rb25/30 and he is fairly sure that the rb30 alternator fits up to the rb20, although the electrical connection is apparently different but can easily be re-wired to fit and in the end is a more cost effective option.

Edited by skypy12
Link to comment
Share on other sites

  • 2 weeks later...

32gtst calipers bolt straight on also

and 33n/a discs slip straight on

32 master cyl (to suit 4spot calipers)

just need to get appropriate brake lines and cut the disc shroud a little and you have budget big front brakes

tried and proven on my car :)

Link to comment
Share on other sites

  • 2 weeks later...
32gtst calipers bolt straight on also

and 33n/a discs slip straight on

32 master cyl (to suit 4spot calipers)

just need to get appropriate brake lines and cut the disc shroud a little and you have budget big front brakes

tried and proven on my car :P

How do 33 N/A discs compare to 32GTS-T discs for thickness? I'm assuming they are the same diameter. I upgraded my front front brakes with the 32 calipers and type-X 180 rotors. They are the same diameter as the 32 discs but slightly slimmer thickness.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • You all are absolute legends! Thank you for helping me put this into context with your comparisons!
    • There's probably an underlying issue with the A/C system too. I recently fixed mine, now it's fully control by the Haltech and car's factory HVAC controller  Have a squiz here:    
    • And by the way, I've also checked the ECU diagnostic numerous times and got a bad O2 sensor code and initially an Ignition Primary code, which is why I replaced the O2 sensor and all the ignition components (coil packa, plug and loom). No codes have been coming up lately despite the ongoing issue.
    • Hey pber13, unfortunately still no luck. At this point the following has been done with little or no success: - Spark plugs replaced, gapped to 0.8mm - Splitfire coilpacks installed to replace originals - Replaced Ignition Coil/Coilpack harness with a new genuine nissan one - New fuel filter - Replaced AFM/MAF sensor - Injectors have been thoroughly cleaned with an online flush (without removing) - Upper engine and inlet decarbed - blew tons of black smoke out, cleared the carbon deposits from the top of the engine and exhaust.  - IACV removed and thoroughly cleaned with carburettor cleaner - O2 sensor replaced with new and genuine one -  Smoke test revealed no vacuum leaks - Healthy compression test of 160psi across all 6 cylinders Overall the car does run a lot smoother now, no backfires between gear shifts like it did originally... but the rough idle when warmed up is still there. It may not even be a misfire but simply a rough idle. Seems crazy to me that so many people have had this issue and seemingly no one has gotten to the bottom of it, or at least never bothered to post if they did! Hope you have more luck than I did pber13, I'm at a point now where I'm just going to try to ignore it unless it gets worse. Would love to fix it but I've genuinely run out of ideas of what it could be.
    • I got the full frenchys kit too. Really awesome kit. Easy to install my only complaint was the hardlines I think could be routed differently (I modified mine) but I realise the kit needs to suit multiple applications. This was the hard lines before I modified them. They were touching the wastegate pipe. I ended up reducing the distance between firewall and first bend. The made it so they tucked along the frame rail.
×
×
  • Create New...