Jump to content
SAU Community

Recommended Posts

Been meaning to post this up for a while now.

1998 R33 GTR

Race Pace Stage 1 Engine

Tomei cam gears

Garret 2860R-5

HKS GT Spec Intercooler Kit

Apex pods

Nismo cat back exhaust with De-Cat

Running ~ 1.2 bar

Everything else is stock standard

Probably only about 270rwkw, as the run would have been done in 3rd gear and not 4th as the standard ECU is still running the show.

post-11439-1233659021_thumb.jpg

ported head matched manifolds

jun guilds stano vavles

stock cams

stock cam gears and springs

baffled sump oil restrictors in the block cam cover plates

jun collar and oil pump

acl race bears mains and big ends

rev rods

cp pistions

1.3mm metal head gaskit

metal inlet manifold gaskits

pfc

stock cooler

stock inj stock fuel pump

stock air flow meters

stock dump pipes

front pipes 3 inch cat 3inch exhuast and cannon

stock turbos

os giken twin plate clutch

eboost 2 set to 13psi

262rwkw!!! 351hp

since the sard 720cc inj sard intank pump

greddy hard pipe kit

gt2860r5s

16psi 400.6hp

now need new coil packs re wire the fuel pump and tuned for more boost

Got mine tuned yesterday. Couldnt push the it to hard as unfortunatley the stock fuel pump isnt playing the game and running out of puff allready, just old age i think.

Autech 260RS stagea

Arias Pistons

Eagle Rods

Trust 264 deg cams

MHG

Balanced throughout

N1 pumps

Tomie oil restrictor and sump baffel

stock cam gears

stock dumps

2860-7's

HKS front pipe and catback

Stock fuel system

Stock FMIC

HKS magic mushrooms

PFC

Stock AFM's

Turbo Tech bleed valve

304AWHP @ a bit under 10psi

car is very responsive.

Need to get a new pump and go for another tune, then start saving for injectors (damn yen)

post-11869-1234830293_thumb.jpg

R32 GTR 85XXX kms

Power FC (Tuned by Mark tillbrook)

GT2860 -7s

700cc injectors

R34 GTR vspec Fuel pump

Stock AFMs

Cat back Exhaust

Made 285kw @ the rears on 15 psi

Need to get a full exhaust system done.

Edited by joeleo87

RB26DETT

Garrett GT2560R 300HP Ball Bearing Turbochargers

750cc Injectors

Apexi Power FC Pro

Apexi AVC-R

Tomei Pon Cams

Cam Gears

HKS Valve springs

Tomei Oil Restrictor

HKS Sump Baffle

Nismo AFM's

Cometic MLS head gasket

Machined and ported head

N1 Water Pump

N1 Oil Pump

Wiseco Forged Pistons

Eagle Con Rods

ARP Heat Stud Kit

ARP Main Stud Kit

Ogura Racing Clutch Twin Plate

Bosch 044 Fuel Pump

Sard Fuel Reg

Splitfire Coils

340kw atw @ 22psi

post-25716-1235554182_thumb.jpg

94 r32 gtr

garret 2860-5

cp piston eagle conrods ect

custom dumps

3inch straight through

nismo fuel pump & afm

sard 700cc injectors

Tomei 260 deg / 9.15mm lift cams+ cam gears

power fc

hks intercooler and piping

sard fuel reg

profect b boost controller

running19psi

made 332awkw

post-43805-1236153353_thumb.png

Edited by tristo
  • 3 weeks later...

Tomei Crank

Tomei Rods

Tomei Pistons

Tomei IN 260 10.85 / EX 270 10.85

PnP head

T04z

1.7 Bar

HKS F Con V Pro

A'PEXi 100mm exhaust

2 nismo lift pumps

2 Bosch 044 externals

800cc Sard

3.5 bar @ idle rail pressure

600*300*110mm FMIC

2 fuel coolers

Nismo Plenum

(and a sh!t load more but that's the main stuff. If people want a full list I will add)

502kW at all 4

Dyno20071114__-1.jpg

DSC01471___.jpg

DSC01492__.jpg

DSC01497__.jpg

DSC01467.jpg

camsdialeddyno.pdf

Cams dialed in now, comparison of before and after graphs, blue latest, red perfect tune but with cams set on 0,0.

for recap,

Stock bottom RB26.

tomei ponB's

GTSS

EVC6

mines stainless pro front pipes, 3.5 inch kakimoto mega N1 rear, tomei manifolds

HKS extension kit,

PFC djetro

436.7 rwhp

Edited by R33GTRKid

R32 GTR

Mystery motor built in Japan

Oil relocation system with oil pump, cooler etc

N1 Fuel Pump

Sard injecters 700 (i think)

PFC

N1 Turbos

HKS Exhaust

Heavy duty clutch (not sure on brand or type)

Blitz intercooler

Apexi AFM and intake

tested and tuned at 1.2bar

235awkw

post-59308-1238634467_thumb.jpg

GTR34

2*T517Z

800cc injector

AVCR

PFC+Z32AFM

Nismo intercooler

Nismo oil pump

Nismo fuel pump (its limited the power, need better fuel system for more power)

Nismo full 3" exhaust + cat(need get 4")

Nismo piping

Apexi super suction kit

turbo smart fuel reg

tomei cam gear in&ex

tomei camshaft both 256 i think.

forged piston, rods

1 bar 270kw

1.3 bar 312kw

R34 GTR V Spec

Turbos

HKS GT2530 x 2

Support

HKS I/C Piping kit incl intake pipes with K&N Filter

HKS Fuel Rail, 680cc Injectors, Fuel Pump and Regulator

Tomei PonCam 260/9.15mm

HKS Cam Gears

Tomei Expreme exh manifolds

HKS Dump Pipes, Front Pipes and Exhaust incl. Metal Cat

Apexi Power FC D-Jetro

HSK EVC V

N1 Water Pump

HKS Twin Plate Clutch

Splitfire Coil Packs

Power

441.9 rwhp @ 17.5-18psi - tuned for as much response and mid range as possible

R34 GTR

Trust 2.7ltr

Willal Head CNC

Holinger box

Hypertune 90mm tb plenum

GT3037s twin kit

Motec M880

535KW at wheels PUMP 1.8bar

575KW at wheels VP109 1.95bar

Motor SOLD - New motor being built

3136hau.jpg

Will post output from new combo soon

OS Giken RB30

Jun "Big" Head

T88H-38GK

Edited by OS30GK

R32 GTR Nismo

Std Nismo turbos

Nismo grounding kit

Std dumps, Bee*R front pipe, metal race cat, kakimoto cat back

std internals

Jun cam gears set to 0

Sard fpr

044 fuel pump

PFC

Blitz boost controller

everything else standard

311kw atw 19psi

Dyno update

-My innovate wideband needs to be calibrated....when I recorded 11.5 afr it was 10.5

-I had the gain too high on the boost controller and it crapped itself at 4400

-I tuned the power fc with my datalogit so it looks like I have some more work to do.

-the 4" Arc Ti exhaust sounds like an animal!

IMG.jpg

IMG_0001.jpg

IMG_0002.jpg

engine mods

-new long block from Nissan

-td-05-16g's in stock housings

-stock injectors and afm's

-trust dp

-3" stainless decat

-4" Arc Ti cat back

-Blitz sbc-id3

-power fc

-20% toluene mix for the dyno

I have new Z32 maf's and 1000cc Rc injectors waiting to go in after I upgrade the turbo's to something else.

R34 GTR V Spec:

* HKS Front pipe, HKS rear pipe with Hi Power Muffler, Hi flow cat

* Garrett 2860R-5 Turbos

* HKS SPL full piping kit with HKS super power flow pods

* Nismo Fuel Pump

* Turbosmart fuel regulator with pressure gauge

* Hypertune Billet fuel rail

* Siemens 610cc Injectors

* OS Giken Cam gears

* Nismo twin plate clutch

* Vipec V44 ECU

* Tech Edge Wideband AFR controller

* HKS EVC6

388 All Wheel Horsepower @ 1.2 Bar (289 All Wheel Kw @ 17.4 PSi) on Insight Motorsports Dyno running 19 inch Volks.

post-43290-1240987077_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I think the consensus was that's normal. Sloped road surfaces or something? I remember @silviaz went through this before. It might be one of those things you never notice until you pay attention to it.
    • Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
    • What do you mean by "seals"? Internal hydraulic seals (ie, is it leaking PS fluid?) or the rack boots that close the rack onto the tie-rods? Because the former is a rebuild, and the latter is trivial that you or any nearby mechanic could do. Dunno about the cowl. Just buy what you think is required and get anything else you find/break afterwards. Wing? Dunno. Don't like R33s enough to pay attention to them. Mirror glass is just glass (on the surface that you want to polish). Go for it.
    • Hello! Long time lurker, been using the forums to address concerns and questions from afar for a while but I've struggled to find some answers so I guess its about time I made an account and formally asked some more knowledgeable people, since finding local skyline owners is hard (and shops that are knowledgeable or trustworthy to work on 'rare' cars are non existent out where im at, as skylines are quite uncommon to find in the wild around here). So the main 3 questions I have, 1: Steering rack has blown seals, well.. they kind of hold but they are not sealed properly anymore and as my R33 is my DD, i cant exactly rip the rack out and send it off or attempt to fix myself. As most refurb ones are around $1,100 or more shipped, and I have other things I need to work on around the car, I was seeking clarification on whether an S15 rack will more or less bolt right in, and whether a common mechanic could do any other required work to get it to fit. I ask, as I've found a supplier than can sell a manufactured as oem one for around 400, if not I'll likely order a used one from Jacks JDM, and take a risk on the seals there. The second question i have is that im replacing the front wiper cowl and have planned to buy 4 new clips and a new center clip but wasnt sure if there were any other clips that would also need to get replaced while I was at it. Given im sure any that are there now will simply break when I remove the old cowl... Last thing would be a fairly straight forward question, i think. If I manage (strong if, finding one has proven to be a pain) to find a R33 GTR spoiler/wing will it require much modification to bolt to a S2 R33 GTST? I've read the bolt patterns dont match but otherwise would bolt in, only options I have found with much luck is China stuff on ebay and carbonetics, which has a nice $650 shipping fee... so if anyone has any pointers where a US chap could locate one that would be great Random side question as well, the mirrors as I understand are mirror glass, and as im planning to polish my windows from water spots and surface scratches, i was hopeful cerium oxide would be fine for them too, as my research points to, but clarification is always nice. Any pointers would be appreciated, and while I have scoured the internet for answers if I missed a prior post somewhere that may answer these directly please point me towards it, as i must have simply missed it. I have seen a post here or there that has mentioned it, but I usually get 50-50 answers, or half answers... I dont have a lot of fab experience or mechanic experience, outside of hydraulic and pneumatic stuff I did in the military and with how hard it is to source stuff in the US, id rather not wing it and hemmoraghe money lol. Thanks guys! Sorry for the monumental first post haha
    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
×
×
  • Create New...