Jump to content
SAU Community

Rb26 Turbo Upgrade, All Dyno Results


SLY33

Recommended Posts

There is some info on the EFRs on this thread, might help .                 "Borg Warner EFR Series Turbo's V 2.0"

From what I have seen the 8374 should liven it up a 1000rpm ish earlier , looks like it really gets going @ 4000 RPM now :)

Link to comment
Share on other sites

  • 2 weeks later...

Updated dyno from yesterday's tuning session. Increased timing from factory Haltech up 3-4 deg. Also increased boost from 17-18 up to a pretty solid 20 psi. BIG changes in HP. This 8374 LIKES THE BOOST. So the car is up about 50 whp over last time at the drags so it should be 10 sec pass on street tires and pump gas this time around. Also they just finished two E85 stations around my house so get ready for REAL power soon!

Getting FUN! Here's comparison to last time at the dyno. Also on this dyno a stock C7 Z06 put down 571 HP/576 TQ so with 14% drivetrain loss it's right at factory claimed 650/650 for comparison purposes (for whatever that matters).

Build is 2.75L BC Stroker crank on stock bores
Tomei Poncam A set 0-0
ported head
BC SS valves
Hypertune V2
CP valve-relieved pistons
BW 8374 IWG .92 turbo
6 Boost Divided T4 manifold
 

 

 

 

dyno MH first v last top HP change.jpg

dyno MH first v last torque dip change.jpg

New dyno MH vs old dyno Hoyt.JPG

  • Like 2
Link to comment
Share on other sites

  • 2 weeks later...
8 minutes ago, ido09s said:

Have you had a chance to race this yet?

keen to hear what mph it runs ;)

134MPH.... didnt stack up to power.... could be due to:

- Not having the boost it was tuned at on the night - should have had 31psi but it was running 29psi

- Me taking it easy during gear shifts due to standard box

Will go back eventually.... blew the box 2 weeks ago so might wait until I have something stronger.

Edited by usmair
Link to comment
Share on other sites

31 minutes ago, usmair said:

134MPH.... didnt stack up to power.... could be due to:

- Not having the boost it was tuned at on the night - should have had 31psi but it was running 29psi

- Me taking it easy during gear shifts due to standard box

Will go back eventually.... blew the box 2 weeks ago so might wait until I have something stronger.

 

All dynos are different mate, even wheels/tyres will make a decent difference. I don't think its too far off the mark though. Our car makes 485rwkw at 23psi and runs 138mph. Unigroup is known to have a bit of a tough dyno though.

Its still decent mph that your car runs. I wouldn't be too concerned about it. Get the box done and race it :)

Edited by ido09s
  • Like 2
Link to comment
Share on other sites

  • 2 months later...
  • 2 weeks later...
  • 3 weeks later...
On Monday, June 20, 2016 at 7:07 PM, .R33. said:
On Wednesday, May 04, 2016 at 5:03 PM, .R33. said:

Hi all just got my R33 GT-R le mans tuned.

Unopened r33 rb26 done just under 100,000 (whether it is legit or not lol)

Mods:

r34 n1 turbos

Ported stock manifolds

Split dump pipes

Xforce front pipes

100cel cat 3"

3.5" cat back

Apexi pods

Trust fmic

Hks evc-5

Link g4+ ecu (no afm's)

Siemens 660cc injectors

Nismo fuel reg

Walbro 255

OS Giken twin plat clutch

Probably more i missed.

Made 300hp on 14psi

365hp on 20psi

Was hoping for abit more after seeing some of the results here, but tuner said to do cams/gears/springs and should get near the 400hp mark.

Added a set of tomei adjustablecam gears. Car now makes 385hp atw 18psi on 98 :) dropped 2psi and gained an extra 20hp...

Impressive gain, wish i did it sooner!

 

Got the gtr flex fuel tuned.

Added a set of splitfire coils, 3.5 inch decat(4inch body), 1000cc injectors, walbro 460 pump hardwired 14v, modified twin turbo plate (divider welded in) ethanol content sensor.

437.7hp @20psi on e85

20170223_173749.jpg

  • Like 1
Link to comment
Share on other sites

2 hours ago, ActionDan said:

You happy with the response given they are N1s?

 

Yes pretty happy, feels like they come on full boost quicker than the dyno paper says. Only driven it twice sine i picked her up and havent really looked at rpm and boost. 

Link to comment
Share on other sites

On ‎23‎/‎02‎/‎2017 at 6:27 PM, .R33. said:

 

Got the gtr flex fuel tuned.

Added a set of splitfire coils, 3.5 inch decat(4inch body), 1000cc injectors, walbro 460 pump hardwired 14v, modified twin turbo plate (divider welded in) ethanol content sensor.

437.7hp @20psi on e85

20170223_173749.jpg

seriously look @ cam gears, should be getting full boost quite a bit before you currently are...

perhaps also consider different dumps if they are the short splits...down the track...

Link to comment
Share on other sites

On 01/03/2017 at 1:51 PM, mr_rbman said:

seriously look @ cam gears, should be getting full boost quite a bit before you currently are...

perhaps also consider different dumps if they are the short splits...down the track...

Tomei Cam gears were put on last year. The dumps are the short split type, when i change turbos to -9's or -5's i will eother go bellmputh or the longer split dumps with matching front pipe. When should i be seeing full boost by? Cheers

Link to comment
Share on other sites

On ‎4‎/‎03‎/‎2017 at 5:47 PM, .R33. said:

Tomei Cam gears were put on last year. The dumps are the short split type, when i change turbos to -9's or -5's i will eother go bellmputh or the longer split dumps with matching front pipe. When should i be seeing full boost by? Cheers

Daniel, I would expect -7's to see fullboost (18-20psi) by 4000RPM, give or take a couple hundred RPM...

If you have cam gears already see what they are adjusted to...

Link to comment
Share on other sites

  • 2 weeks later...

Here is my results 

R33 GTR

stock head apart from arp head studs n tomei type b valve springs n retainers 

gtw3884r 62mm 1.00 ts

6boost ts t4 mani 

turbosmart 60mm gate 

3.5" tbe 

100mm fmic

bosch 1000cc 

walbro 460

turbosmart v2 1200

458rwkw @ 28psiIMG_1980.thumb.PNG.edaf5f020a696b09376daa25332cb3d6.PNG

 

 

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Surprisingly the D6000 is only $1999, I'm waiting for the BF/CM sales, and hoping to get one cheaper. D4000 is well priced, still outperforms the 13" SVS PB-3000 and is like 1/2 the price at $1699 RRP. I do watch a fair amount of movies, and listen to EDM, jazz, symphonies, etc. so the lower notes from a subwoofer are always appreciated. The front 8" stage, just doesn't provide you with lively feeling, even though they are pretty bassy for a pair of large bookshelves. Then again, these days it's just playing Wiggles, Blippi and Ms Rachel, another reason the 3m wide cabinet exists, to hide all the audio gear behind it. They used to sit on a nice pair of stands, but as you know, they make good baby traps too.
    • Granted, which is a solid reason why I don't have one. My floorstanders are only -2 dB at 22 Hz.  So they're still working down to <20 Hz. Which is no doubt part of the reason why my receiver shits the bed! That Tonewinner would be about double the cost though, so it's not apples and apples. There aren't many AU$1300 subs (that you can buy prebuilt, I'm ignoring what can be achieved by DIYing) that compete.
    • -6dB at 22Hz isn't that great, watch the data from the D6000 from REW
    • I'll just leave this here. https://www.adelaidespeakers.com/subwoofers.html TL loading, big power. They sound awesome. This is what I would buy if I was going to try to take the bass away from my floorstanders. Just go with the 12".
    • I'll snap up some photos when I'm back home, in the office today meeting my "in the office" quota. Have 2x Teams calls scheduled in, office culture they reckon.   I've never owned a proper off the shelf sub, I've always made or modified broken ones with Jaycar plate amps and/or car subwoofer drivers. The current (and broken) subwoofer has a proper home driver in it, Dayton driver, thos one https://www.daytonaudio.com/product/118/rss265hf-4-10-reference-hf-subwoofer-4-ohm FS of 25Hz, which is low but not low enough. Yeah, I think they were brought out to the market to compete with SVS. I would love a SVS PB-3000 but they're not cheap, especially after their price hike. From reviews online, it does look like the Tonewinner D6000 would destroy and with good amount of money saved too.
×
×
  • Create New...