Jump to content
SAU Community

Fs: R33 Various Parts

onBOOST247
 Share

Recommended Posts

onBOOST247 Enthusiast

onBOOST247

Posted
Posted (edited)

Cleaning up.. Have a few bits and peices lying around..

1. 1x Stock R33 BOV, working in perfect condition $30 o.n.o

2. 1x Stock Intercooler from R33, few stock pipes aswell, perfect condition $50

3. 2x R33 OEM Electric Sunroof Motors, perfect $50 each

4. 1x R33 Rear passenger quarter trim , perfect $50

5. 1x R33 Centre console, handbrake boot also, $50

6. 1x Passenger Door trim Damaged, can be repaired $30

7. 1x Drivers Apillar $15

8. 1x Passenger A Pillar $15

Anyone make an offer, just taking up space..... Want to get rid of it very soon.,

Located in Sydney, NSW , can post at buyers expense.

Andrew

0412 675 321

Edited by onBOOST247
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Is this pressure plate warped? And do I need a new one?

      By joshuaho96 · Posted

      Pretty simple question. I was about to put the transmission back in and thought I pretty much had it lined up when I noticed it seems like the pressure plate isn't flat. I was pretty careful when undoing the bolts both during initial disassembly for cleaning and when torquing them up for installation so this is pretty discouraging. I'm not sure if I accidentally bumped the pressure plate with the input shaft and bent it somehow or if it just showed up this way. Is it possible that there's just something obvious I'm not doing correctly? I'm pretty sure I was extremely careful to make sure the friction discs were seated correctly in the hub, everything lined up, flywheel torqued according to sequence, the little springs all sitting correctly in their seats, etc.  What's the play here? Do I jump straight to a new pressure plate?
    • GTSBoy
      Nismo 1.5 way Stub axle issue

      By GTSBoy · Posted

      OK. I can see that being the case. But if you live in the land of "only switching between 4.08, 4.11, 4.36" like most Skyliners, then you never encounter it. Now I perhaps understand why the crownwheel is thicker on some of the smaller numerical ratio diffs. The two stubs being the same (unequal) lengths and just swapped side to side between the different cases is a new one to me. I'm hating Nissan R200s more than ever now.
    • Butters
      RB gearbox options

      By Butters · Posted

      Reason I say this is I have seen broken ones, in drift, drag and even behind a stock Z. I do appreciate most of the time its the synchro's that go.   Trouble with quoting HP is it doesn't really say how strong the box is.  I've not seen many CD00X box's make it past a mid 9(150mph) I have seen about a stock R33 RB25 box's run a 9 too, they all go boom at some point though.   Another clue is they make gearsets for CD00X box's too, wouldn't be a market if they didn't break or have a limit people are going past.   I totally agree it is a strong box, just have to weigh up the true total cost of the conversion vs rebuilding with a good gearset. 
    • TurboTapin
      RB gearbox options

      By TurboTapin · Posted

      What makes you say CD009 boxes are not as strong as you would think? I've always been told the last revision (CD00A) is good for 1000whp and I have no issue's believing it when comparing one side by side with an RB25 box. Makes them look tiny. 
    • OO Dan OO
      Nismo 1.5 way Stub axle issue

      By OO Dan OO · Posted

      I picked up an open Center with shafts. I was told the Open shafts will fit a mechanical LSD and looking at them. I think they will work. Will update 
×
×
  • Create New...