Jump to content
SAU Community

Recommended Posts

Hi all,

A bit of a tricky question that I hope some guys will be able to shed some light on for me.

Does anyone use a novated/operating lease for imports?

It’s a common practice at my work to use novated leases that breaks down as follows:

A car is purchased through Fleet Australia on behalf of the employee.

Repayments are then paid BEFORE tax for the period of the lease (say three years)

At the end of the lease the car has a residual value of say 30% which the employee can pay to own the car outright. This can be profitable as most cars don’t drop below 30% residual after three years which means you can buy the car and sell it at a profit.

The benefits of a novated lease are substantial for those of us earning in excess of $40,000-$50,000 are taxed almost half of each dollar for the top parts of our income. As the car payments come out 'pre-tax' our taxable incomes are therefore less.

In simple terms $10,000 repayments in one year only cost the employee $5,400 in “take home income”

Now the reason for my post. I want to novate lease an R34 GTT however my company will only allow us to buy new so I want to get my own novated lease and charge the costs back to the company so I can get my import.

Does anyone do this already? If so which company are you novating through????

I tried to get my car through a novated lease... answer was NO. Basically because it's a grey import that is not on their list of supported cars. Also, the car is "too old" the be considered for their terms and conditions (they need a relatively new car so that they can still make money when they sell it off)

Besides, since these types of arrangements include all on-road costs (insurance, fuel, and rego etc.) I don't think they would bother with a car that they have very little return on.

i was one of the last few guys to get a skyline through prosperion cos they chagned their rules, well the underlying esana did. no more grey imports. i had mine on a 2 year lease.

all tyres maitenance servicing rego insurance was paid for as part of the lease and i had pre tax payments come out of my wage. i then got taxed on the change. so in theory you get paid less and pay less tax and get a car as result. had no issue with payout figure or anything and all was happy. got a fuel card too so more optimax than you can poke a stick at. a friend has an xr6 turbo on a lease too. it's a ute so you don't pay FBT cos its not considered a "benefit" as it only has two doors and two seats. mine was considered a "benefit" so i had to pay FBT. but in the whole scheme of things FBT aint that much. you dont have to record ODO for fuel but it is recommend to. you get posted each quarterly fuel report and ODO readings.

youll've have no chance of getting a grey import on lease IMHO, damn nice if you do though. I asked a few places re: GTR33 or GTR34 and none were keen to touch it after esadan had said no more grey imports

Depends on your provider, a lot accept second hand veheicles subject to conditions. Our one had the proviso that so long as the car was no older than eight years old at the end of the lease it was okay.

//edit: subject to their final approval on the choice of vehicle :)

Hi, I lease my R33 through NLC, This is the company my work deal with. My lease covers everthing, ie: fuel, services, tyres, maintance insurance. Its all part of the package. i was the first person to lease an import through NLC so the paperwork took a bit longer. Its a great way to pay less tax and get the car you want.

My R33 GTR is on a novated lease.

I had trouble getting it on the GTR tho. THey didn't want to do it because they had a rule of 'no car older than 5 years at the end of the lease' or something along those lines. I did manage to drag out of them that it was just the finance part they didn't want to do. So i asked if i could find external finance, they said yes. I found external finance via NLC via maquarie... they rigged it all up and off i go... thats the short version it was a little bit more of a struggle than that, but i got it in the end. 4 year lease... all lease repayments/maintence/petrol/insurance pre-tax... but yes i do have to pay FBT, it still saves me thousands of $ per year.

QuickR33: your figures are a bit wack, if your making less than 58k per year, then you are in the 30% tax bracket, not the 47%... so your comment

"In simple terms $10,000 repayments in one year only cost the employee $5,400 in “take home income”"

should be

"In simple terms $10,000 repayments in one year only cost the employee $7,000 in “take home income”' etc...

it depends on yoru tax bracket. most lease companies have calculators on thier website for novated lease.

There is also a novated lease WITH ECM (employee contrib meathod), which i'd recommend taking over a normal novated lease.. you'll save a bit mroe money again....

I did my R32 GTS4 through Novation Leasing Company (NLC Pty Ltd).

Level 3, 102 Albert Rd, S Melbourne

8699 7000

www.nlc.com.au

But that was nearly 6 years ago now. Can't hurt to talk to them

NLC is who got me my finance on my GTR for my works novating leasing company. They were very helpful.

As for modifications, wouldnt' you call that 'maintence' - i do :huh:

"ohh my exaust broke, i need a new one, maintenence"

"my wheels were buckled, o well need a new set"

only thing you need to watch out for is insurance, like any other insurance policy.

NLC is who got me my finance on my GTR for my works novating leasing company. They were very helpful.

As for modifications, wouldnt' you call that 'maintence' - i do :(

"ohh my exaust broke, i need a new one, maintenence"

"my wheels were buckled, o well need a new set"

only thing you need to watch out for is insurance, like any other insurance policy.

I had completely forgotten that lingo! Why of course it is maintenance. I used to use the same one with parents on their cars when I was at uni.

"The stereo has chewed up my tape, I need to repair it with a CD player"

"The CD player I put in, was too powerful for the speakers and has blown all the speakers, so I had best sort those out now"

End of uni my dad asks me why he has 6x9's in the back of the car, a changer and sub in the boot and a Sony headunit with more buttons than an aircraft flight deck that he is never going to understand :lol:

Ah good old maintenance :lol:

Some good answers guys :P

What happens with modifications on a novated lease out of interest? Can you modify and are there any technicalities to watch for?

Generally, you still own the car, so I guess you are free to do anything (legal) that you want to it. You will need to cost any intended mods into the lease cost, because you will end up paying for them one way or the other.

yeah mods are fine just have the workshop fit what you want and get them to charge it back to the lease company as like new wheel bearings, new bushes for suspension that sorta stuff and its fine.

yep basically anything you modify is maintenance which is nice. Even consumables like r tyres! Not to mention tax deductible petrol.

But be aware that 48.5% tax doesn't kick in until $95k this year, and it is going to $120k next year....which means that far fewer people are in the top bracket and so it is less worth getting a lease....check the figures carefully

I visited the site above and did some calculations on their slidy scale based on purchase price, salary and KM's and I would work out about $500 better off doing it that way. Think I will stick with the one I am with currently for ease.

Interesting read guys :D

Yep, Duncans right about tax brackets... but you don't need to be in the highest tax bracket to have it work out better.

Mean_R34 is right as well, if you do less than 25,000ks in a FBT year you pay 20% FBT, if you do 25000-40000 you pay 11%, anything over 40000/y is 9% FBT....

saff_cossie, The sites probably didn't include all the maintence you would use - that would all be pre-tax and GST free :D

Like i said, mine saves me a few grand a year.... I even bought my new gearbox via the least... so that would of cost me $3300 out of my pocket if i didn't do it through the lease, but since i did, i got the GST back ($300), and it was pre-tax, so lets say i was in the 30% tax bracket, that would save me another 30% since its paid for pre-tax... so it now cose me closer to $2,000 rather than $3,300.... saves me $1,300 right there.... if your in a higher tax bracket, you'll save even more....

As for the others who asked how you get it, your company has to offer novated leases - its a bit of paper work and hassle for them, and most companies would probably say 'no, its to hard'...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can perhaps see how the R33 appreciators would think so.  
    • Thanks, I removed the fuse and the relay from the car and made my own circuit with them to test them with a test bulb.  I will look for the wiring diagram and go from there.
    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
×
×
  • Create New...