Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

The Mixture is really dependent on how much you want to muck around with the engine tune. Toluene is less volitile and so tends to have cold start issues at low temps (after today it looks like theres no chance of that for a while).

For a straight replacement of bp 98 to drop the 'ping' factor, run around with about 10- 15% with a 95/96 octane fuel.

I run upto 30-35% for short periods. It cleans out your fuel system while its at it too. This requires a tune to suit.

There are probably others with experience around who might like to share their prefferences too.

The price for a tin is actually $32 now. Diggers brand. For a 20L drum it's $97. If people like to they can shop around for a hardware store willing to get it in regularly at a better price in my opinion the hardware store is charging abit much since they changed from being a Makit brand store.Even at $32 I preffer this over the 500ml octane bottle no brand comes even remotely close.

appart from more power. Toluene will increase the exhaust temps a tad but, it's lower volitility means much increased tollerence to pre-ignition. You run it a little on the rich side of 11:1 to be safe if your a backyarder playing with timing.

Oh and the catylitic converters don't like this additive for very long periods without appropriate tuning.

here is an old extract I have about it;

Toluene is a pure hydrocarbon (C7H8). i.e. it contains only hydrogen and carbon atoms. It belongs to a particular category of hydrocarbons called aromatic hydrocarbons. Complete combustion of toluene yields CO2 and H2O. This fact ensures that the entire emission control system such as the catalyst and oxygen sensor of your car is unaffected. There are no metallic compounds (lead, magnesium etc), no nitro compounds and no oxygen atoms in toluene. It is made up of exactly the same ingredients as ordinary gasoline. In fact it is one of the main ingredients of gasoline.

Toluene has a RON octane rating of 121 and a MON rating of 107, leading to a (R+M)/2 rating of 114. (R+M)/2 is how ordinary fuels are rated. Note that toluene has a sensitivity rating of 121-107=14. This compares favorably with alcohols which have sensitivities in the 20-30 range. The more sensitive a fuel is the more its performance degrades under load. Toluene's low sensitivity means that it is an excellent fuel for a heavily loaded engine.

Toluene is denser than ordinary gasoline (0.87 g/mL vs. 0.72-0.74) and contains more energy per unit volume. Thus combustion of toluene leads to more energy being liberated and thus more power generated. This is in contrast to oxygenated octane boosters like ethanol or MTBE which contain less energy per unit volume compared to gasoline. The higher heating value of toluene also means that the exhaust gases contain more kinetic energy, which in turn means that there is more energy to drive turbocharger vanes. In practical terms this is experienced as a faster onset of turbo boost.

have fun...

oh and it's deadly poison and you'll all die die die !!! HA HA HA!

Is there any octane boosters that you guys recommend. Also.. how much do I add to a full tank of petrol, do i go the premimum + octane booster or just get the shitter commoner fuel + octane booster. Just wondering how much I add to bring it up to, or better than ultimate 98

http://www.nitrous.com.au/products.html

Comes highly reccomended by a few garages. How good it really is, i don't know. I put 1/2 a bottle of yellow into my tank for the purpose of injector cleaning, but i don't feel any difference. LoL. Cause for all u know, it just the garage pushing their product (they stock it), and when they stock it, high chance they wanna earn ur $$. But hey, it's made in WA! Supports WA! LOL!!!

bp along orrong rd (pretty sure the is only one heading towards farmer freeway) has ultimate, and so does bp in bullcreek along perry ave..and u can save 4c a litre there too wif dewsons or supa valu dockets :(

jus shop around and luck :( sum places run out of premium not 98..and apparently shell's premium is 87..not 95 or 96. so it beats votex which is ova rated :D

Toluene rotting fuel lines:

............actually yes it does and your whole car will start rotting shortly afterwards and then the neigbours dog too but, no one liked it barking at night anyway so we are all happy again. Although without fuel lines and a car.

It also will cause you girlfriend to leave you and it will lose you your job.

..and apparently shell's premium is 87..not 95 or 96. so it beats votex which is ova rated :)

Nah your wrong dude, don't know where you got that info. I'm telling you all now.. normal unleaded petrol is 91-92 RON, most premiums are 95-96 (VORTEX is 96) and BP Ultimate is 98.

Octane booster is pretty much useless guys. Yeah it helps a bit and most of them also clean out injectors and prevent knocking etc. But wont give you much of a performance gain.

Say you fill up with VORTEX (96RON), and you add in some octance boost which gives you "7-8 points", this will make your petrol 96.7 - 96.8 RON.

BP Ultimate still leads with 98RON.

10 points of octane boost = 1 RON.

Hope this helps :P

Edited by Br4nchi3

even IF it were true that fuel lines rot from tolulene

compare the cost effectiveness of replacing fuel lines, o-rings and fuel pump, with

rebuild of engine

hmm, tough choice. Seriously guys, dont listen to old wives tales, I have used tolulene, Rev210 has used tolulene, I know many people that regularly use tolulene (with other additives like avgas :) ) and NOT ONE of them, nor me has had any problems with rotting fuel lines

Next time someone tells you it rots fuel lines, ask them if its from personal experience, if they say no - its just a rumour, if they say yes, ask them how long they were using it until the fuel lines rotted, what percentages, and how old the fuel lines were to start with. I am sure they will get very vague about their answers at this point.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...