Jump to content
SAU Community

Recommended Posts

Ok last night i meet a guy with a Stock R32 GTR also, he checked out my car and said nice I/C. I thought and still think its a std I/C

BUT.....he is convinced mine is a 97 V-spec Cooler. Because it doesnt have the lines going through it. Can any one tell the difference, which comes to my next concern, someone told me i have a Tight rear LSD because at low speeds while turning it is jumpy. others say it is std.

Link to comment
https://www.sau.com.au/forums/topic/9523-types-of-ic-off-gtrs/
Share on other sites

Judd - I'm not sure if you can tell that if your car is jumpy it is due to the LSD. but then again I'm not an expert..

Also as far as I know I didn't think theres any difference at all between the regular GTR and Vspec intercoolers. I have a HyperRev that shows all the differences in the models between Series 1,2 and 3 GTR's and the Vspecs and it doesn't mention anything about coolers....

Hi Guys from what I can tell;

* the R33 GTR I/C has one more row of tubes than an R32 GTR I/C

* the tubes themselves are slightly bigger in diameter than an R32 GTR I/C

* there are visible weld joins on the tubes, that are either not there on an R32 GTR I/C or can't easily be seen.

I have not had an R32 and an R33 I/C together in the one place at the one time. It has been a couple of years since we had the R32 GTR I/C and I have just got an R33 GTR I/C and these are the things I remember as looking different.

What I can tell you for certain is, on the flow bench, the R33 GTR I/C flows about 5 to 8% more air at 500 bhp with 1.5 psi resistance. Turning that around, it flows the same amount of air with around 1 psi less resistance.

Hope that adds to the information bank.

Sydneykid,

Your car says R32 GTST RB31DET have you got a bored out 3litre block in your R32, must be a bit of a beast!!

and nismogtsx:

The R33 keeps the RB26DETT engine from the R32 GT-R. The power is still the same with an official 280hp (206kw) at 6800rpm, although inofficially it is ass-umed to be around 302hp. Increased peak turbo-boost of 0.84bar, an improved intercooler and changed computer control parameters make for a higher torque of 375Nm (271 lb-ft) at 4400rpm. As usual, power is deployed via the 5-speed Getrag gearbox and ATTESA-ETS to all four wheels.(from http://www.infinitig35.net/R33/GTR/index.php)

so sydneykid is right!!

MEGA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...