Jump to content
SAU Community

Gb: R33 Gts-t And Gtr And R34 Gtt Radiator Guides


Recommended Posts

  • Replies 520
  • Created
  • Last Reply

Top Posters In This Topic

I pilot an R33 SII with the stock airbox. These radiator guides actually impede the airflow to the stock airbox since the intake snorkel sits on top of the radiator support?

I pilot an R33 SII with the stock airbox. These radiator guides actually impede the airflow to the stock airbox since the intake snorkel sits on top of the radiator support?

hmm this sounds interesting...i'll wait to hear bass junky's response before buying 1 of these as i'd be putting it on a S2 R33 as well

Depending on the design of your front bar, normall the guide actually tilts down from your radiator support panel.

The guide will actually scoop air INTO the inlet duct of your car.

You can then use some foam and guide the air into that duct.

BUT, if the duct does look like blocking air getting to the inlet duct, I can include a scoop section on the guide to allow better airflow to the inlet duct.

Send me some photos of your front bar on the SII with the bonnet up, looking at it from the front.

my cars still on its way, but ive got the pics they took in japan for me....stock S2 front bar...

post-22515-1132630240.jpg

and sorry if im completely wrong, but looking at my pic, and then the pic you put up of the guide, it looks like it blocks the airflow to the radiator through the grill ? :S

Edited by dezz

yeah like i said, im only going by what i can see. do you have a diagram of how they guide the air or anything? might clear it up for others and not just me...

thanks

the snorkel bolts to on top of the radiator support beam, as opposed to the radiator guide which will bolt onto the side of the support beam, so it shouldn't restrict flow to the snorkel.

if postage is under $15ish (which will then make it cheaper than UAS) and it fits a R33 S2 with this grill, then put me down for one.

IMG_0001.jpg

yeah like i said, im only going by what i can see. do you have a diagram of how they guide the air or anything? might clear it up for others and not just me...

thanks

33gtstairguide.jpg

This is the UAS one, you can see the snorkel is above this air guide.

thanks dan, but what i meant was that the radiator itself looks to be blocked...

like in my pic u can see the radiator through the gap...and the guide covers that?

im probably wrong, as these have been designed to improve air flow etc, but i just cant see how atm.

is their some sort of support on the front edge of the guide? or is it just bolted on at the radiator support?

i'm interested for r33 s2 style front bar and grill (same as lordsnipes pic)

like in my pic u can see the radiator through the gap...and the guide covers that?

I don't think it'll be that much of a prob. The radiator is huge, and unless you have a HUGE FMIC which completely covers the radiator, i don't think you would have any problems in regards to cooling.

Whilst there are supposed benefits of cooling (such as air not being able to escape through that gap and forced through the radiator), I'd think it's more of a cosmetic item than performance.

Edited by lordsnipe

i thought the whole idea of an air guide was to trap and force the air thru the radiator?? so thats exactly what its doing by sealing it off.

in ur first pic bass ur guide seems to be flat where as the uas is angled, are you able to make it angled??

ill wait till i see the final design before i say yes.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • In a few years from now, you'll regret that. It'll eat away at you, knowing the truth of the ugly hiding beneath the beautiful exterior... 😛
    • I don't think the G2 profile is particularly dangerous for the engine per se, more just are you actually ok with the turbo lag trade-offs? If the answer is yes then go for it. I personally don't think I'd be ok with it because I spend so much time at lower RPMs and I really enjoy the feeling of being able to stay in 5th gear on the highway and just roll into the throttle to get boost. Or staying in 3rd gear on "gentle canyon cruises" without feeling the turbo lag too badly. The 525 pump should be able to run flat out on factory lines but I would bet the pressure drop from pump to regulator is quite impressive. I don't know how much it would be exactly but I've seen figures like 30 psi thrown around.
    • It's interesting seeing everyone talk about what level of risk they are happy to tolerate.  Building a GTR always has a level of risk, you could be that lucky guy that drops 20k on the engine build alone and still has the thing go pop on the dyno. Life is fun like that.  The way I see it, the thing is a toy to be enjoyed. I'd be happy to turn up the power on stock motor and limit the risk with sensible tuning and engine protection. If it still goes pop, it is what it is. The car isn't a daily driver so it can happily sit while a plan is made to sort it out.  Given this thing will be a street car only, I really feel it's worth the (relatively small if managed well) risk to turn the power up to around 350KW on e85.  I don't think anyone getting into the skyline game now is doing it out of logic. Surely it is a purely emotional decision so I'm not sure how important it is to think about the engine build logically. The heart wants what it wants.  @joshuaho96 little note for Josh, I run my 525 pump flat out all the time and through the factory lines without any issues. (excluding the melting connectors, that's sorted now. we'll pretend it never happened lol)
    • But the Nexus S3 is very expensive and won't be as purpose-built for the application as a separate electronic boost controller :^) More seriously my pet issue here would be that the Walbro 525 running at 100% duty cycle is going to require more FPR than the stock setup can handle. I'm also pretty sure from what I've seen elsewhere you might want to slow down the pump regardless unless you're going to come up with some way of upsizing the fuel lines coming from the fuel tank. Factory 8mm fuel line doesn't actually flow very much if you want to keep pressure drop down between the fuel pump outlet and FPR. If you really want to "keep it simple" I would run only as much pump as you need and source a fuel pump controller to slow down the pump in the vain hope of being able to run stock-style FPRs which are pretty dinky. Or just use the HICAS lines and it should be mostly fine. OP should also really think hard about what profile they'd want out of the turbo. My pet choice here would be the G1 profile rather than anything higher power but YMMV. I already think ~stock turbo lag is pretty bad so I don't want to make it worse. In "gentle canyon cruising" I found that I spent a lot of time around 4-4.5k RPM. I also recommend DIYing labor if you're detail-oriented enough. Costs are high for labor + if you do it yourself you can be your own quality control.
    • GTSBoy is again on the money. My actual advice? Sell the car. (really). For what it's worth as is, you can sidegrade into something much better. If you care about function then this is the actual move. If you want a Skyline to perform, set aside about $100K to do it. This is NOT a typo. You will see right away these are two very different mindsets. Realistically we're talking full restomod for any Skyline still kicking around. Have an honest think about which one you are.. and what you want to do, and how much you want to invest in this (with no return).
×
×
  • Create New...