Jump to content
SAU Community

Engine Stalling After Installing Bov Need Help Pls

Nismo Racer

By Nismo Racer,
in Engines & Forced Induction

 Share

Recommended Posts

Nismo Racer Mentor

Nismo Racer

Posted
Posted

Hi, my car is a S1 R33 GTS25t and the BOV in question is a Blizt DD. After intalling the BOV when breaking into a shape corners the engine will stave of air and stall on me. I have try this a number of times and it still stall on me BTW the car is AUTO. I think it's the hose overheating or the ECU is not use to the BOV yet. I have reset the ecu and will test some more on the weekend. did anyone have any problem like this before? maybe because i'm not running a pod.

Also can anyone please attach a pic of the engine bay with apexi pod installed with stock AFM.

Thanks in advance.

paulr33 Grand Master

paulr33

Posted
Posted

atmo bov you have. atmo bov no worky. it vents air, the engine expects that air is still be there so it adds fuel / timing to suit however the air is not present so it runs too rich and stalls. fix use stock bov

The Mafia Grand Master

The Mafia

Posted
Posted (edited)

dude, you can't fix it.

Well, actually you can. Either plumb back your BOV or put the stock one on.

Why would you bother putting a loud fully sik OMG!!!!111oneoneone!!!11 BOV on a auto anyway.

Do you drive around, foot flat, and taking it off the throttle quickly to make your BOV vent on purpose when there are some fully sic chiks around?

Let me guess, you're a poser?

hhmmm

atmo bov you have. atmo bov no worky. it vents air, the engine expects that air is still be there so it adds fuel / timing to suit however the air is not present so it runs too rich and stalls. fix use stock bov

This is why your Fully sic BOV is making your car stall. You run an AFM before the BOV, it measures air that is gonig into the motor and the ECU puts fuel and timing in to suit.. Use a Vent to ATMO BOV and it takes away this air and leaves the fuel behind..

And what do you know.. that fuel doesn't have that air anymore to burn, so it stalls, pops, farts, and carries on.

If you want to run a fully sic ATMO bov, get a powerfc d-jetro and run a MAF at the throttle body.

That'll make the chicks look....

oh and if your wondering why your getting a lot of smart assed answers...Next time, try using the SEARCH function, this topic has been covered about 34568938930295345 times, by people that have no idea about the car they drive. They think you just turn the key and the wheels go magically. And they also seem to think that if you install a Vent to atmo BOV all the chicks will line up and want to ride with you.

lol can't believe I typed all of that.

Edited by The Mafia
lordsnipe Community Regular

lordsnipe

Posted
Posted

why does everyone say use the stock? If he wants the sound, he is entitled to it.

It's all about the setting of the BOV. I got a Greddy Type-S and my car doesn't stall at all! It's all about adjustment, tighten the spring and it should stop stalling, but don't tighten too tight otherwise it'll flutter and the BOV isn't actually doing its job.

The only side effect of an atmo BOV is that it'll be rich when the BOV vents, and you may get a bit of backfire, especially after letting off on hard throttle.. but being an auto, you won't get rich conditions on gear changes.

having said that, yeah, he should get flamed for not searching.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Any Tech feed back? thx

you got it within the first 8 words of the first reply

atmo bov you have. atmo bov no worky.

simply put, you wanna use an ATMO BOV... you'll need to purchase a SAF-c/PowerFC and have the thing tuned so that it wont spit the dummy

This can be found by searching and reading, trust me :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • thomasLait
      New Stegea Owner

      By thomasLait 路 Posted

      Hey everyone, I recently bought myself a 2001 Nissan Stegea M35, and I've had a few issues that I had to fix, my car would start intermittently and I had a bad rocker cover leak, after a couple days of looking I finally found a part number that interchanges with the OEM starter as the OEM starters at $1300 and I can't afford that, this starter was only $270 and I replaced the start and still had the same issues, I posted a video asking for help online and it went very well, some guy said it was probably a bad ignition switch so I took my dash apart and turns out my ignition switch was half screwed in and was loose, once it was tightened it fired right up, I found a local place called "Boost factory" and they sold me a part of OEM Nissan rocker covers, they were $600 which was a shocker but I couldn't find them anywhere else, so I installed them and fixed my oil leak as the old rocker cover was cracked and warped, I now need to replace my boost air inlet hoses as they have some cracks.
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a 路 Posted

      I am being real ocd and do not want to make amy mistakes so appreciate all help provided. I am overly cautious so asking for opinion even if i know the answer   few questions,   1.re tensioner, should spring be greased lightly?    2.tensioner has two washers , one pressure washer and other has recessed/ seat. I am going to put the recessed one facing tensioner where edges are cut out and pressure washer on top   3. my car has custom triger kit sold few years ago by guy who initially built the engine. I moved the crank gear and it moved in and out easy, only way to remove belt is to slide the crankshaft gear forward which I did. I have seen these being very tough to move , anything to do with my woodruff key?   it has a crank sensor shown in purple which I assume reads from the 12 teeth position mounted to the crankcase gear   4. timing belt doesn鈥檛 have arrow stating front or back just a arrow which I think is direction of rotation . Do you agree?   5.i figured out why my crankcase cover was worn as there was no washer installed over the crankcase cover before the harmonic balancer was put in place. It is missing, anyone knows the part number? It looks like this https://justjap.com/products/genuine-nissan-crankshaft-timing-gear-rear-plate-washer-nissan-s13-ca18-a31-r32-rb20-r33-r34-c33-c34-c35-rb25?currency=USD   https://tinypic.host/image/IMG-4535.382Zy2 https://tinypic.host/image/IMG-4537.382dSz https://tinypic.host/image/IMG-4534.382q4U  
    • TurboTapin
      New fix for low tyre pressure from bmw

      By TurboTapin 路 Posted

      CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah 路 Posted

      My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Dose Pipe Sutututu
      Another little story of weird shit happening

      By Dose Pipe Sutututu 路 Posted

      Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
脳
脳
  • Create New...