Jump to content
SAU Community

Recommended Posts

hey Darren. the bosch pump has worked great for me so far. i know Nightcrawler has had some problems with the 040, though. then again i have heard bad things about the walbro aswell. do a search in 'forced induction performance' too, there are quite a few fuel-pump threads that mention these two pumps. :P

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738637
Share on other sites

Darren,

I have had a bosch o40 or 044( cant remember) for many years now ( in fact martin d did an artical in hpi on how to do a in tank fit using our car as guinea pig for fit / photo's_at tilbrook's ).These are quite good pumps, we have had no trouble however they are on the noisy side with no music pumin!

Regards,

SKYLINE (Kym)... B)

Edited by skyline
Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738783
Share on other sites

Cheers guys just read the forced induction section and it seems they are quite similar in performance whilst the Walbro is some $60 cheaper and the bosch 040 can have some issues with fittment(eg the 1/4 tank which could cause surging issues). Cheers Kym might have to find that HPI Mag as i will be doing it DIY styles.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738816
Share on other sites

hey, the "1/4 tank" problem with the 040 is due to incorrect fitting of the pump in the first place, nothing to do with the pump itself.

sydneykid is not a fan of walbro pumps (which is enough for me, to be honest) and another guy i spoke to who has an escort race car said "nothing but bosch". you should be able to pick up an 040 for about $220-230 or less.

how much power are you planning on making? the 040 will be fine up a point but you might need something bigger. but then don't go for overkill or you get noise and overheated fuel (depending on your setup)...

cheers

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738929
Share on other sites

Yeh the 040's are about $235 delivered where as Walbro are $175 delivered, yeh i was originally more keener on the 040 after hearing about issues with the Walbro, but now they seem to be quite similar, Thinking i might have to spend the extra cash and get the better quality one(040).

After AFM and a FC retune should be up around the 210-220kw mark which i will be happy with for a while.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738953
Share on other sites

i got my 040 from Greddy in the Trader section for 230 delivered, came all the way from great brittan.

i heard about that surging problem, on the bottom of the 040 there seems to be no nozle to connect that pick up hose thingy?? as all the other pumps habve them that maybe be the problem. i DUNNO really. :)

havent fitted it yet coz im a slack bastard :D

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739312
Share on other sites

I took out my Bosch 040 that was noisy as hell (especially when you have below 1/4 tank or the weather is over 30 degrees) and put in a Walbro 255lph. Have had the car dynoed with both pumps and power is the same, at the same fuel rail pressure. I had the Walbro rechecked just the other week, after hearing disparaging comments from some SAU users, but Turbo Tune said the pump gave 'more than enough' fuel pressure for 200rwkw through 4 x 550cc injectors. They could not fault the pump whatsoever, yet I did have a 4 month old Bosch 040 fail year back.

Edit: Like DriftR says, the oem style mesh pickup of the Walbro is far more reassuring than the Bosch pump setup - the Bosch has no filtering and the pickup is not as low down (which could explain people's surging problems).

Edited by Nightcrawler
Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739315
Share on other sites

Having an 040 installed right at the moment (with z32 afm, fpr, fuel lines, sitc, direct battery feed to fuel pump, etc yadayadayada), and retuned on the safc.

Hopefully pick it up tonight...

Yah, have read that Walbro isnt that great but is serviceable, big thing there is the amount of cheap chinese copy Walbro pumps that are out there. Nasty stuff apparently. Read a lot about that. But also read genuine items flow like a 040.

With the 040, you must install it as low down in the tank as possible, to get around that 1/4tank surge 'feature'. Due to the pump not having a 'sock' like the 918-series. Install low down with a custom bracket, and that wont be a problem.

I got my Bosch 040 off ebay (victoria, fordefi) for $198 delivered, with 12month warranty.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739943
Share on other sites

I got my 044 installe din the 32 by Shaun. Cant hear it at all, excpet on hot days it gets a little noisy.

Turbo Tune said the pump gave 'more than enough' fuel pressure for 200rwkw through 4 x 550cc injectors.

Id expect them to say something like that regarding a skyline :)

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1745863
Share on other sites

I needed to get a new fuel pump after I did a SR20DET conversion in my Silvia, and went for the Bosch 040. It makes a buzzing noise every 5 seconds or so on idle usually, but can't usually hear it much when driving normally. As others have said though, it's almost constant noise when you are low on fuel. Doesn't bother me, I just don't pay attention to it.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1745866
Share on other sites

I got my 044 installe din the 32 by Shaun. Cant hear it at all, excpet on hot days it gets a little noisy.

same with mine too. shaun installed it, and it never makes a sound. except yesterday when the weather was warmer than usual, i could hear it.. why is that?

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1746228
Share on other sites

When the weather is warmer your fuel is warmer. When the fuel is warm it expands. When the fuel is warm/expanded the pump has to work harder to pump the same volume of fuel, compared to a cold day when the fuel is more dense. The pump working harder is the noise you hear.

When I had my 040, on any day when my car had been out in the sun for a while and the temp was over 30 degrees, the buzzing noise was horrible.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1746259
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Very nice - I also have a 92 GTST and hardly see any others around these days
    • When I need something else to edit, I use Movavi. A friend who does video editing on a daily basis recommended me) it's an easy video cutter to use for beginners
    • I need to edit some videos for work but I'm not good at all this. Which video editor can you recommend?
    • I think you're really missing the point. The spec is just the minimum spec that the fuel has to meet. The additive packages can, and do, go above that minimum if the fuel brand feels they need/want to. And so you get BP Ultimate or Shell Ultra (or whatever they call it) making promises to clean your engine better than the standard stuff....simply because they do actually put better additive packages in there. They do not waste special sauce on the plebian fuel if they can avoid it. I didn't say "energy density". I just said "density". That's right, the specific gravity (if you want to use a really shit old imperial description for mass per unit volume). The density being higher indicates a number of things, from reduces oxygen content, to increased numbers of double bonds or cyclic components. That then just happens to flow on to the calorific value on a volume basis being correspondingly higher. The calorific value on a mass basis barely changes, because almost all hydrocarbon materials have a very similar CV per kg. But whatever - the end result is that you do get a bit more energy per litre, which helps to offset some of the sting of the massive price bump over 91. I can go you one better than "I used to work at a fuel station". I had uni lecturers who worked at the Pt Stanvac refinery (at the time they were lecturing, as industry specialist lecturers) who were quite candid about the business. And granted, that was 30+ years ago, and you might note that I have stated above that I think the industry has since collected together near the bottom (quite like ISPs, when you think about it). Oh, did I mention that I am quite literally a combustion engineer? I'm designing (well, actually, trying to avoid designing and trying to make the junior engineer do it) a heavy fuel oil firing system for a cement plant in fricking Iraq, this week. Last week it was natural gas fired this-that. The week before it was LPG fired anode furnaces for a copper smelter (well, the burners for them, not the actual furnaces, which are just big dumb steel). I'm kinda all over fuels.
    • Well my freshly rebuilt RB25DET Neo went bang 1000kms in, completely fried big end bearing in cylinder 1 so bad my engine seized. No knocking or oil pressure issue prior to this happening, all happened within less than a second. Had Nitto oil pump, 8L baffled sump, head drain, oil restrictors, the lot put in to prevent me spinning a bearing like i did to need the rebuild. Mechanic that looked after the works has no idea what caused it. Reckoned it may have been bearing clearance wrong in cylinder 1 we have no idea. Machinist who did the work reckoned it was something on the mechanic. Anyway thats between them, i had no part in it, just paid the money Curiosity question, does the oil system on RB’s go sump > oil pump > filter > around engine? If so, if you had a leak on an oil filter relocation plate, say sump > oil pump > filter > LEAK > around engine would this cause a low oil pressure reading if the sensors was before the filter?   TIA
×
×
  • Create New...