Jump to content
SAU Community

Recommended Posts

hey Darren. the bosch pump has worked great for me so far. i know Nightcrawler has had some problems with the 040, though. then again i have heard bad things about the walbro aswell. do a search in 'forced induction performance' too, there are quite a few fuel-pump threads that mention these two pumps. :P

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738637
Share on other sites

Darren,

I have had a bosch o40 or 044( cant remember) for many years now ( in fact martin d did an artical in hpi on how to do a in tank fit using our car as guinea pig for fit / photo's_at tilbrook's ).These are quite good pumps, we have had no trouble however they are on the noisy side with no music pumin!

Regards,

SKYLINE (Kym)... B)

Edited by skyline
Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738783
Share on other sites

Cheers guys just read the forced induction section and it seems they are quite similar in performance whilst the Walbro is some $60 cheaper and the bosch 040 can have some issues with fittment(eg the 1/4 tank which could cause surging issues). Cheers Kym might have to find that HPI Mag as i will be doing it DIY styles.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738816
Share on other sites

hey, the "1/4 tank" problem with the 040 is due to incorrect fitting of the pump in the first place, nothing to do with the pump itself.

sydneykid is not a fan of walbro pumps (which is enough for me, to be honest) and another guy i spoke to who has an escort race car said "nothing but bosch". you should be able to pick up an 040 for about $220-230 or less.

how much power are you planning on making? the 040 will be fine up a point but you might need something bigger. but then don't go for overkill or you get noise and overheated fuel (depending on your setup)...

cheers

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738929
Share on other sites

Yeh the 040's are about $235 delivered where as Walbro are $175 delivered, yeh i was originally more keener on the 040 after hearing about issues with the Walbro, but now they seem to be quite similar, Thinking i might have to spend the extra cash and get the better quality one(040).

After AFM and a FC retune should be up around the 210-220kw mark which i will be happy with for a while.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1738953
Share on other sites

i got my 040 from Greddy in the Trader section for 230 delivered, came all the way from great brittan.

i heard about that surging problem, on the bottom of the 040 there seems to be no nozle to connect that pick up hose thingy?? as all the other pumps habve them that maybe be the problem. i DUNNO really. :)

havent fitted it yet coz im a slack bastard :D

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739312
Share on other sites

I took out my Bosch 040 that was noisy as hell (especially when you have below 1/4 tank or the weather is over 30 degrees) and put in a Walbro 255lph. Have had the car dynoed with both pumps and power is the same, at the same fuel rail pressure. I had the Walbro rechecked just the other week, after hearing disparaging comments from some SAU users, but Turbo Tune said the pump gave 'more than enough' fuel pressure for 200rwkw through 4 x 550cc injectors. They could not fault the pump whatsoever, yet I did have a 4 month old Bosch 040 fail year back.

Edit: Like DriftR says, the oem style mesh pickup of the Walbro is far more reassuring than the Bosch pump setup - the Bosch has no filtering and the pickup is not as low down (which could explain people's surging problems).

Edited by Nightcrawler
Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739315
Share on other sites

Having an 040 installed right at the moment (with z32 afm, fpr, fuel lines, sitc, direct battery feed to fuel pump, etc yadayadayada), and retuned on the safc.

Hopefully pick it up tonight...

Yah, have read that Walbro isnt that great but is serviceable, big thing there is the amount of cheap chinese copy Walbro pumps that are out there. Nasty stuff apparently. Read a lot about that. But also read genuine items flow like a 040.

With the 040, you must install it as low down in the tank as possible, to get around that 1/4tank surge 'feature'. Due to the pump not having a 'sock' like the 918-series. Install low down with a custom bracket, and that wont be a problem.

I got my Bosch 040 off ebay (victoria, fordefi) for $198 delivered, with 12month warranty.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1739943
Share on other sites

I got my 044 installe din the 32 by Shaun. Cant hear it at all, excpet on hot days it gets a little noisy.

Turbo Tune said the pump gave 'more than enough' fuel pressure for 200rwkw through 4 x 550cc injectors.

Id expect them to say something like that regarding a skyline :)

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1745863
Share on other sites

I needed to get a new fuel pump after I did a SR20DET conversion in my Silvia, and went for the Bosch 040. It makes a buzzing noise every 5 seconds or so on idle usually, but can't usually hear it much when driving normally. As others have said though, it's almost constant noise when you are low on fuel. Doesn't bother me, I just don't pay attention to it.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1745866
Share on other sites

I got my 044 installe din the 32 by Shaun. Cant hear it at all, excpet on hot days it gets a little noisy.

same with mine too. shaun installed it, and it never makes a sound. except yesterday when the weather was warmer than usual, i could hear it.. why is that?

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1746228
Share on other sites

When the weather is warmer your fuel is warmer. When the fuel is warm it expands. When the fuel is warm/expanded the pump has to work harder to pump the same volume of fuel, compared to a cold day when the fuel is more dense. The pump working harder is the noise you hear.

When I had my 040, on any day when my car had been out in the sun for a while and the temp was over 30 degrees, the buzzing noise was horrible.

Link to comment
https://www.sau.com.au/forums/topic/96012-fuel-pumps/#findComment-1746259
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...