Jump to content
SAU Community

Modifyin R33 Interior/dash

teamplasma
 Share

Recommended Posts

teamplasma Community Regular

teamplasma

Posted
Posted

Hey guys, i've decide to modify my dash while it's out and the cars at the paint shop. It's an r33 dash, at this stage i've got 4 autometre gauges which i was going to mount in the dash in from of the passanger, a shift light tack which is going on the a pillar and i was wanting to mount my apexi avcr scrren on the dash, but like cover it some how, I'm thinking about covering the dash in fibreglass moulding the bits into place and having the whole think spray painted in a gloss white and maybe a little air brush work, my only concer is the fibreglass my eat into the dash, any ideas on how to overcome this or any new ideas at all? i'm not keen on leather by the way, any pics, or constructive critizim is welcome

Link to comment
https://www.sau.com.au/forums/topic/97187-modifyin-r33-interiordash/
Share on other sites
sproosy Grand Master

sproosy

Posted
Posted

cool idea but what i dont get is why would you have all these gauges in front of the passenger? Can you see them and read them from the drivers seat?

If its a show car then thats all good. As far as fibre glassing and stuff, sounds good, but if its black you will see every bit of dust that sits on it.

have fun

**JaR** Grand Master

**JaR**

Posted
Posted

yeah thats true. unless you clean your car religiously you will always see them little dust specks everywhere. it is a pretty cool idea though.

one question.... why the tach? the standard tach is quite readable.....

shift light is ok, but there really isnt a need for an aftermarket tacho.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By soviet_merlin · Posted

      Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...