Jump to content
SAU Community

Recommended Posts

Sky30,  I have not personally compared the two gearboxes side by side fully dismantled, but know someone that has.  There is one bearing with a different Nissan part number, not sure which, but both bearings are physically interchangeable and probably make no real practical difference. It is the sort of production change that car makers sometimes make during a production run.

The 4WD gearboxes are essentially otherwise identical in all respects, and used in both GTR and GTS-4. Gears, casing, shafts, selectors, seals, transfer case, everything are absolutely identical.

Diffs are the same too. R160 in the front and R200 in the rear all are 4.11 ratio except the R32 which has 4.32 diffs.  The rear LSD can be viscous, multi-plate, or electronic, depending on what was ordered.  Some GTS-4s even have the electronic diff usually only seen in the V spec GTR, though that is extremely rare.

The R34 GTR with the six speed Getrag has different gear ratios and diff ratios again, (3.54, I think ?). The front diff is an R180.

I was also tols the GTS4 transfer case has less clutch packs than a GTR?

GTS-4 and GTR gearboxes are identical, except that the R32 GTS-4's (with the RB20DET) used different ratios. The R33 boxes and diffs are identical ratios.

But driveline strength also must include the clutch and half shafts. The GTS-4 is considerably less than the GTR in both clutch capacity and rear half shaft diameter. It also uses four stud wheels.

If you get an R33 GTS-4 and put a GTR clutch in it, and upgrade the wheel hubs and half shafts, it will be identical to a GTR in both strength and ratios.

But an R32 GTS-4 will have different ratios, but could be made just as strong with the same clutch and driveshaft changes.

Ginkgo Biloba i was replying to this post.

Targa spec GTRs put out around 250rwkw, so not big power. But 30 6000rpm launches in 6 days as well as a season of 8000rpm race launches are a pretty good test.

Standard diffs, standard gearbox. We regularly have to replace gearboxes with synchro problems but we've never broken anything inside. Never had any trouble with the diffs they are a pretty strong piece of gear.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...