Jump to content
SAU Community

Recommended Posts

hey all just bought a 4 door 32 and i had coil packs tested, they were stuffed got new splitfire coil packs and irridium plugs and put them in and a new oxygen sensor also went in. and i still seem to have a rather bad misfire or hesitation while im driving the car on boost or not.it is running an auto mines ecu and car is manual and the plug on the cat convertor has been cut off in japan so the dash light flashes constantly can anyone help me please.

i have also checked afm

any help would be much appreiciated

MYP16

Link to comment
https://www.sau.com.au/forums/topic/97555-r32-hessitating-very-bad/
Share on other sites

also may sound stupid, check your oil level

where any vacuum hoses changed? i know i had problems when i used bigger hoses for my turbo's bleed valve and blow off set up, started causing a lil drama's

also take out those irridiums and get some ngk copper plugs, ull have less drama's

Edited by nemz
hey all just bought a 4 door 32 and i had coil packs tested, they were stuffed got new splitfire coil packs and irridium plugs and put them in and a new oxygen sensor also went in. and i still seem to have a rather bad misfire or hesitation while im driving the car on boost or not.it is running an auto mines ecu and car is manual and the plug on the cat convertor has been cut off in japan so the dash light flashes constantly can anyone help me please.

i have also checked afm

any help would be much appreiciated

  MYP16

My Suggestions;

1. What plug gap? Should be 0.8 mm, not 1.1 mm as they usually come.

2. Have you checked the ignition timing? Autos run more initial ignition advance than manuals, it may be necessary to set the timing at 20 degrees instead of 15 degrees. Try both and compare.

3. Have you had a leak down test done? Results?

4. I have never seen a Mines ECU work very well in Australia, get a hold of a standard ECU and compare. You could spend much time and money chasing other things when the ECU is the real problem.

5. Pull the bulb in the cat overheat warning light.

Hope that helps

:( cheers :)

un plug the 02 sensor. it sounds silly but it will eliminate it as a problem. evan if its new it could be the wrong one.

also if you can get hold of a fuel presure guage it would be handy.,tell the mechanic to test it while hes up it.

(be carful not to place it under the wipers as i broke a windscreen doing it that way)

does it have a foam type airfilter,or any aftermarket air filter?

from what it sounds like these are my main suspect parts:

1-air flow meter

2-fuel pump

3-02 sensor(will be ok when cold but f**k out after about 2-3 mins)

4-ignition igniter.-finned thing at the back of the motor

5-coolant temp sensor

if had to fix a whole heap of these problems with cars coming of the boat, and its usaly in that order.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I suppose that's true. Barring almost any situation, I'll never sell so what the market does is kind of irrelevant to me. It's possible I'd make most of my money back. That spreadsheet I mentioned? Maybe I could make back more than what the car's total costs thus far are, but the parts and all that is possibly a different story... Thanks for reading. It was certainly a good moment and just makes the ties to the car that much stronger. It's exciting that the option will be there to bring it over, however I have some plans with a shop that may end up keeping the car there longer, not sure. Coupled with the fact I want to move there and haven't solidified any path yet. So in a way, it feels like I'm in a limbo state that is uncertain; time will tell.
    • No worries, everything worked out in the end. I just wanted to make the point that it doesn't matter where it comes from (I.E Australia), it can be broken or improperly built. I would still purchase from these companies in the future. B2R - Not certain how that finished, this was on a car I wired a few things and street tuned. I know the owner ended up shipping the motor back to Australia for investigation. Hopefully some of it is covered under warranty.  Turbosmart - I always pressure test everything that goes on my car. It's a habit from my career in oil and gas. I run two 40mm's and both had major leaks from the actuator to exhaust portion through the shaft. I returned both, they shipped me back two and one was leaking and the other had a 38mm top (40mm gate with 38mm actuator cap, no idea how that happens). Eventually after a lot of back and forth I found myself with two non-leaking gates. I believe this happens a lot more then people would like to believe but you would never know if you don't pressure test them prior to installation. Crank Motorsport - Issued a full refund and let me keep the seat rails. I turned them into scrap metal for other projects. GKTech - Shipped me out a replacement and asked that I modify it as per my idea and that they would do the same for a future revision. ATP - Can just needed a large shim to bolt up properly.  Haltech - They started an actual proper Beta channel for firmware's a few months back and stopped using the general public for testing. I'm now much happier.  Speedtek - f**k Speedtek. I would love to watch them burn.     
    • I've got a Turbosmart wastegate, ATP catch can, many GK Tech parts and Haltech everything. Everything's been perfect, sorry to hear your experience wasn't the same
    • The only high-power RB I've personally seen go pop after running for all of an hour on a dyno was built by B2R, while being remotely tuned by B2R. The only wastegates I've ever had leak like a sieve, return, still leak, return and get shipped back the wrong ones were from Turbosmart. The only final drive that I've ever purchased that were unusable, twice... were from Speedtek. The only seat mounts that I've ever purchased that placed the seats in the door frame were from Crank Motorsport. The only poorly designed parts that I had the manufacturer confirm should have been designed as per what I mentioned were from GKTech. The only ECU I've had firmware updates consistently break things are Haltech. The only catch can I've purchased that didn't fit in its advertised spot was from ATP. So forth and so on... Moral of the story, doesn't matter where it's from. Do your research beforehand and stick with products and companies you've trusted in the past.    @joshuaho96 If you want it done right, do it yourself.
    • Something coarse-ish. 180 is good.
×
×
  • Create New...